Bravetti BP101H2 - Manual (Page 5)

OPERATING INSTRUCTIONS
French Fry Blade Assembly
CAUTION: Make sure that the unit is
unplugged from the power source and
the operating button is “OFF” before
inserting or removing attachments.
Note: The French Fry Blade is already
assembled to the blade holder. Do not
try to remove it. (Fig. 13)
1. Make sure that the blade storage
cover is closed during use.
2. Fit the processor bowl and spindle
as detailed previously.
3. Using the finger holes in the French Fry
blade holder, fit it over the spindle and
press firmly into place as indicated.
(Fig. 14)
WARNING: USE EXTREME CAUTION
WHEN HANDLING BLADES. BLADES
ARE SHARP.
4. Fit the lid and click into place as
indicated in Setting Up section
(page 4).
5. Plug in the processor.
6. WARNING: USE THE FOOD
PUSHER TO ADD FOOD INTO THE
PROCESSOR BOWL THROUGH
THE FEEDER TUBE.
Do not overload the bowl. In one
operation, you can process a
maximum 5 cups (1250 ml) of food.
Fig. 13
Fig. 14
Processing Examples
For fine slicing: Blade A - Recommended speed level is MAX
(Cucumbers, raw potatoes, lettuce, carrots)
For coarse slicing: Blade B - Recommended speed level is MAX
(Cabbage, carrots, onions)
For fine shredding: Blade C - Recommended speed level is MAX
(Carrots, cucumbers, cabbage)
For coarse shredding: Blade D - Recommended speed level is MAX
(Lettuce, carrots, apples)
For Grating: Blade E - Recommended speed level is MAX
Blade A Blade B Blade C Blade D Blade E
7
OPERATING INSTRUCTIONS
8
Juice Extractor
CAUTION: Make sure that the unit is unplugged from the power
source and the operating button is “OFF” before inserting or
removing attachments.
1. Fit the processor bowl as detailed in the manual (page 4).
2. Fit the juice extractor/filter into the processor bowl.
3. Fit the juice extractor lid over the extractor and rotate counter
clockwise ensuring that the lid tab has clicked into place.
4. Plug in the food processor.
5. Turn speed control to low (use only on low speed).
6. Use the juice extractor pusher to add fruit into the food tube.
7. If the juice extractor becomes clogged during use, turn the
processor off and remove the juice extractor. The excess pulp
can now easily be removed using the spatula.
Be sure to switch the appliance to “OFF” position after each use.
Make sure the motor stops completely and unplug the unit before
disassembling.
FOR SAFETY, ALWAYS USE THE PUSHER WHEN PUTTING
FRUIT INTO THE FEEDER TUBE - NEVER FEED BY HAND.
Do not put your fingers or other objects into the juicer opening
while it is operation. If food becomes lodged in the opening, use
food pusher or another piece of fruit or vegetable to push it down.
When this method of removing food lodged in the opening is not
possible, turn the motor off, unplug unit and disassemble juicer to
remove the remaining food.
CAUTION: Make sure that the unit is unplugged from the power source and the
operating button is “OFF” before inserting or removing attachments.
1. Fit the processor bowl
as detailed in manual
(page 4).
2. Fit the citrus juice filter
into the processor bowl.
3. Rotate counter
clockwise. Ensure that
the citrus juice filter tab
has clicked into place.
4. Insert the juice reamer into the
center of the citrus juice filter
with its shaft inside the central
column of the bowl.
5. Plug in processor.
6. Place fruit on juice reamer and hold
with a cupped hand.
7. Operate at lowest speed.
WARNING: ALWAYS OPERATE THE
JUICER AT LOWEST SPEED
ONLY. DO NOT OPERATE THE
CITRUS JUICER AT HIGHER
SPEEDS.
WARNING: ALWAYS OPERATE THE JUICER AT LOWEST SPEED ONLY. DO
NOT OPERATE THE CITRUS JUICER AT HIGHER SPEEDS.
Citrus Juice Filter