Salsbury Industries 4325 Roadside Mailboxes 2-Wide and 3-Wide Spreader & Pedestal - Manual

SALSBURY INDUSTRIES
1010 East 62
nd
Street, Los Angeles, CA 90001-1598
Phone: 1-800-624- 5269 Int’l Phone: 323-846-6700
Fax: 1-800-624- 5299 Int’l Fax: 323-846-6800
www.mailboxes.com engineering @ mailboxes.com
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
Copyright © 2014 Salsbury Industries. All rights reserved. (Rev. 02, 2/19/14)
Roadside Mailboxes
– 4325
2-Wide and 3-Wide Spreader & Pedestal Installation Instructions
U.S.P.S. APPROVED
Thank you for selecting Salsbury’s 4325 roadside mailbox. This instruction sheet is for installing 4325 mailboxes on a 2-wide or 3-wide spreader and a pedestal. A
different instruction sheet is available for installing 4325 mailboxes on a 4-wide spreader and a pedestal. Other installation instructions are available for installing the
mailbox on a pedestal, or on a deluxe mailbox post, installing the mailbox on a newspaper holder, and installing the pedestal in a concrete footing.
When you install a curbside or roadside mailbox, make sure that it is easily accessible to the mail carrier. By regulation a locked mailbox should be 41” to 45” from
the ground or street surface up to the point of mail entry. The door should be set back 6” to 8” back from the front face of the curb or the road edge. However, you
should check with your local postmaster to ensure that the mailbox is installed according to local regulations. It is important to note that it is not the responsibility of
mail carriers to open mailboxes that are locked, accept keys for this purpose, or lock mailboxes after delivery of the mail.
Installing Mailboxes on Spreader & Pedestal
4382 2-Wide Spreader
All hardware to attach the spreader to the pedestal is included with the
spreader. To attach the spreader to the pedestal, install four (4) 5/16”-18 X
1” long hex flange head bolts through the four (4) center square holes of the
spreader and through the four (4) tapped holes on the top plate of the
standard mailbox post. Cover the hex flange head bolts with cap plugs.
All hardware to attach the mailboxes to the spreader is included with the
spreader. To attach a mailbox, open the front door or rear door of the
mailbox and install four (4) 5/16”-18 x 1-3/4” long carriage bolts through the
four (4) square holes in the inside floor of the mailbox, through the square
spacer, and through the four (4) corresponding square holes in top of the
spreader. Install 5/16” flat washers and 5/16”-18 hex nuts on the ends of the
four (4) bolts protruding below the bottom of the spreader. Repeat these
steps for the other mailbox. Installation is now complete. Additional
hardware provided is not needed and may be discarded.
4383 3-Wide Spreader
All hardware to attach the spreader to the pedestal is included with the
pedestal. To attach the spreader to the pedestal requires simultaneously
attaching the center mailbox to the spreader and to the pedestal. Start by
opening the front door or rear door of the center mailbox and install four (4)
5/16”-18 X 2” long pan head bolts through the four (4) square holes in the
inside floor of the center mailbox, through the square spacer, through the
four (4) center square holes of the spreader, and through the four (4) tapped
holes on the top plate of the pedestal.
All hardware to attach the remaining two mailboxes to the spreader is
included with the spreader. To attach an additional mailbox, open the front
door or rear door of the mailbox and install four (4) 5/16”-18 x 1-3/4” long
carriage bolts through the four (4) square holes in the inside floor of the
mailbox, through the square spacer, and through the four corresponding
square holes in top of the spreader. Install 5/16” flat washers and 5/16”-18
hex nuts on the ends of the four (4) bolts protruding below the bottom of the
spreader. Repeat these steps for the other mailbox. Installation is now
complete.