Salsbury Industries 4325D Designer Roadside Mailboxes Deluxe Mailbox Post - Manual

SALSBURY INDUSTRIES
1010 East 62
nd
Street, Los Angeles, CA 90001-1598
Phone: 1-800-624- 5269 Int’l Phone: 323-846-6700
Fax: 1-800-624- 5299 Int’l Fax: 323-846-6800
www.mailboxes.com engineering @ mailboxes.com
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
Copyright © 2013 Salsbury Industries. All rights reserved. (Rev. 03, 2/19/141/13)
Designer Roadside Mailboxes
– 4325D
Deluxe Mailbox Post Assembly Installation Instructions
Installing Arm(s) on Deluxe Mailbox Posts
Thank you for selecting Salsbury’s deluxe mailbox post. This instruction sheet is for assembling the 1-sided or 2-sided deluxe mailbox post. All hardware to
assemble the deluxe mailbox post is provided.
When you install a curbside or roadside mailbox, make sure that it is easily accessible to the mail carrier. By regulation a locked mailbox should be 41” to 45” from
the ground or street surface up to the point of mail entry. The door should be set back 6” to 8” back from the front face of the curb or the road edge. However, you
should check with your local postmaster to ensure that the mailbox is installed according to local regulations. It is important to note that it is not the responsibility of
mail carriers to open mailboxes that are locked, accept keys for this purpose, or lock mailboxes after delivery of the mail.
4370 – 1 Sided
First check to see that all the parts and fasteners in the carton have been
located and identified according to the illustration below. Also refer to the
illustration below to position the parts correctly.
1. Attach the small right-angle bracket to the post with the long leg on top
with two (2) 5/16”-18 x 2” long pan head bolts.
2. Attach the long square-tube arm to the small right angle bracket with two
(2) 1/4”-20 x 1/2” long flat-head socket screws.
3. Attach the large decorative arch to the post and the long arm with four (4)
5/16”- 8 x 1” long hex flange head bolts. Cover with cap plugs.
4. Attach the other small right-angle bracket with the long leg on the bottom
with two (2) 5/16”-18 x 2” long pan head bolts.
5. Attach the short square-tube arm to the small right-angle bracket with two
(2) 1/4’-20 x 1/2” long flat-head socket screws. This completes the
assembly.
4370 Assembly
4372 – 2 Sided for 2 Mailboxes
4373 – 2 Sided for 3 Mailboxes
4374 – 2 Sided for 4 Mailboxes
First check to see that all the parts and fasteners in the carton have been
located and identified according to the illustration below. Also refer to the
illustration below to position the parts correctly. The 4373 has the same
parts as the 4372, except one (1) arm is longer. The 4374 has the same
parts as the 4372, except the two (2) arms are longer.
1. Attach the small right-angle bracket to the post with the long leg on top
with two (2) 5/16”-18 x 2” long pan head bolts.
2. Attach the long square-tube arm to the small right angle bracket with two
(2) 1/4”-20 x 1/2” long flat-head socket screws.
3. Attach the large decorative arch to the post and the long square-tube arm
with four (4) 5/16”-18 x 1” long hex flange head bolts. Cover with cap plugs.
4. Repeat steps 1 through 3 above for the second arm on the other side of
the post. This completes the assembly.
4372, 4373, 4374 Assembly