X-1 (H2O Audio) S8-1A3 - Manual (Page 4)

7. Closing the Housing
4.
Inspect the Seal Area after closing to ensure that you have a tight seal
between the Tray and the Silicone Sleeve. Ensure there are no gaps
between the Silicon Sleeve and Tray, they must be completely flush.
If you have any concerns, please repeat the Leak Test from Section 4.
3.
Slide the Silicone Sleeve all the way
to the top of the Tray, until it mates
tightly. Do NOT slide Silicone Sleeve
over the Clip located on the back
of the housing.
2.
Ensure the shuffle’s Control
Pad and the Control Pad of
the Silicone Sleeve are both
aligned and facing up.
1.
Make sure the shuffle is turned ON before closing the housing.
There is no access to the power or shuffle Switchs when the housing is
closed.
Make sure a small amount of “Super O-Lube” is present on the Tray and
the Silicone Sleeve before assembling them together. This will help
maintain a watertight seal, and facilitate the opening and closing of the
housing.
CAUTION: If too many uses occur between the application of the Super O-Lube,
a watertight seal cannot be guaranteed. Please apply a small amount of
Super O-Lube at least every 5 separations of the Tray and Silicone Sleeve.
** For more Super O-Lube please contact H2O Audio’s Customers Support **
2 3
6. Installing the iPod shuffle 2 nd Gen into the Tray
Removing the iPod Shuffle 2 nd Gen
4.
Turn on the iPod shuffle 2 nd Gen before
installing the Tray in the Silicon Sleeve.
There is no access to the power or shuffle
switchs once in the Silicon Sleeve.
3.
Push the iPod shuffle 2 nd Gen all the way
onto the stereo plug until the shuffle is
seated completely within the Tray.
2.a
1.
Remove any skins or protective covers
from your iPod shuffle 2
nd Gen.
The Tray that holds the iPod shuffle 2 nd Gen is what protects your shuffle
from impact and water. It acts as an exoskeleton around your shuffle,
and provides support to the soft Silicone Sleeve of the housing.
Installing the iPod
3.
2.
Slide the iPod shuffle 2 nd Gen into the
Tray (Control pad MUST be aligned
with the 5-hole pattern see 2.a ) and
line up the 3.5mm stereo plug of the Tray
with the 3.5mm stereo jack on the iPod
shuffle 2
nd Gen.
1.
Turn the Tray over to expose the back
with the Clip facing up. Using your
thumb to block the opening at the
bottom of the Tray will prevent the
shuffle from falling out once
disconected. Gently pushing the shuffle
down, unplugging it from the Tray and
slide out.
shuffle
Tray
Clip
5. Opening the Housing
1.
Using one hand, secure the
Lanyard. (at least 2 fingers
are recommended)
Opening the housing is very technique sensitive, and we recommend you
practice opening and closing the housing a few times.
THE SILICONE SLEEVE IS NOT EASILY SEPARATED FROM THE TRAY.
THIS IS WHAT KEEPS YOUR IPOD SHUFFLE 2
nd Gen SAFE AND DRY.
NOTE: Grabing the Silicone Sleeve at the highest point possible on the Finger
Grips will help open the housing.
2.
Using your other hand, squeeze
the Finger Grips of the Silicone
Sleeve at the Seal Area and pull
the Silicone Sleeve away from
the Tray.
3. Introduction
4. Leak Test
The H2O Audio waterproof housing allows you to listen to digital audio during
active watersports. This housing accomadates the Apple iPod shuffle 2
nd Gen
digital media player only.
HOUSING: The housing features a Silicone Sleeve that intimately mates with the
hard plastic (polycarbonate) Tray. The housing allows for functional control of
the iPod shuffle 2
nd Gen control pad.
NOTE: There is NO access to the power or shuffle switches on the iPod shuffle
2 nd Gen when the waterproof housing is closed.
NOTE: The shuffle is NOT waterproof without the H2O Audio housing and
headphones, and is NOT covered under the product warranty. Any attempt
to use the housing with an audio player other than the Apple iPod shuffle
2
nd Gen will void the Warranty.
HEADPHONES: The housing is only waterproof when combined with H2O
Audio Waterproof Headphones (sold separately). Use of other headphones
with a 3.5mm stereo connector will result in a water resistant case, and
should not be submerged.
Before utilizing the system for the first time, it is highly recommended to
perform a 'Leak Test'. Follow the instructions below.
1. Open the housing (Section 5), and verify the seal area is clean and free of debris.
2. Close the housing (Section 7) and attach H2O Audio Waterproof Headphones.
3. Immerse the housing, (without the iPod shuffle 2
nd Gen) in water and soak for 30 min.
4. Manipulate the Control Pad during submersion.
5. Remove from the water, dry the exterior.
6. Open the housing.
DO NOT INSTALL THE iPod shuffle 2 nd Gen
INSIDE THE HOUSING FOR THE LEAK TEST
NOTE: When the Silicone Sleeve is separated from the Tray, water droplets
will sometimes deposit on the side of the Tray. This does not indicate a leak,
it is a typical result when separating the housing.
2. Housing Features
IMPORTANT: Make sure the top of the Tray mates tightly with the Seal Area
each time you close the housing. This is required to keep the housing
watertight. Remove any skins or covers from the shuffle player prior to use.
Silicone Sleeve
Clip
Lanyard
SealTight TM Connector
Control Pad
Finger Grip
Tray
Seal Area
Printed Instructions
Before using this system, please be sure to read, understand, and follow the instruction of this manual.
www.h2oaudio.com
H2O Audio for iPod ®
shuffle (2 nd Gen)
H2O Audio housings and cases are designed for specific Apple iPod models,
which vary by generation and storage size. You must ensure the correct
housing or case is purchased for your specific iPod model.
S8 - 70 20070713