Rockwell Automation 800T_H Illuminated Selector Switch - Manual (Page 2)

40063-296-01 (B)
MADE IN U.S.A.
Table 1
Gaskets required for various panel thicknesses.
Units are shipped with three 1/16 in. (1.6) gaskets
16 gauge 1/16 in. (1.6)
12 gauge 7/64 in. (2.8)
10 gauge 9/64 in. (3.6)
3/16 in. (4.8) 3 gaskets
2 gaskets
2 gaskets
1 gasket
Panels thicker than 3/16 in. (4.8) must be counterbored to
3/16 In. (4.8) thickness.
NOTE: Dimensions shown in parentheses are in millimeters.
1. Remove lens mounting ring and knob or knob lever assembly.
2. Remove lamp by inserting the lens removal tool onto the lamp, push
down and rotate counter clockwise. Pull out the lamp.
3. Install a new lamp of the correct number. Refer to nameplate for lamp
number. Push lamp into socket using the lamp tool. (Cat. No.: 800E-ALR1)
Rotate clockwise and pull lamp tool out once the lamp is retained.
4. Reinstall the lens assembly by placing the assembly over the shaft.
NOTE: The shaft has a projection which should line up to the knob
indicator. Thread the lens mounting ring onto the bushing once the
knob is seated on the shaft.
An operator may be used with 1 or 2 of the contact blocks listed in Table 2,
except as noted. Multipleblocks must be mounted in tandem and may be in
various combinations, two blocks maximum.
Table 2
Number of Contacts
Standard Block
Cat. No. 800T–
Pen TUFF TM
Low Voltage Blocks
Cat. No. 800T–
Logic Reed
Block
Cat. No. 800T–
Sealed Switch Block
Cat. No. 800T–
Stackable Sealed
Switch Blocks
Cat. No. 800T–
1 N.O. – 1 N.C. XA 800T-XAV XAR XAP 800T-XAY
1 N.O. XD1 AND XD5 800T-XD1V XD1R XD1P 800T-XD1Y
1 N.C. XD2 AND XD6 800T-XD2V XD2R XD2P 800T-XD2Y
1 N.O. (Early Make) XD3 XA2R
1 N.C. (Late Break) XD4 XA4R
1 N.C. (Late Break) – 1 N.O. XA1
1 N.C. (Late Break) – 1 N.C. XA7
2 N.O. XA2
2 N.C. XA4
1
1
3
3
4
2 4
4
N.O. = Normally Open N.C. = Normally Closed
Sealed switch contact blocks may only be mounted singly, directly behind
the operator. (no stacking)
3 Mini contact blocks 800T-XD5 and XD6 may not be mounted directly
behind the operator, stack only on top of another contact block.
4 Hermetically sealed contacts – may be used in Class 1 Division 2
hazardous location applications in an enclosure suitable for the
environment, which need not be a hazardous location enclosure. (Refer to
National Electric Code)
PREFERED METHOD (4.4)
11/64
(17.1)
43/64
(46.8)
1–27/32
(57.2)
2–1/4
ш
(ш30.6) 1–13/64
ш 1/4 DRILL
(ø6.4)
ALTERNATE METHOD
Minimum
Spacing
Spacing
Figure 2. Hole Recommendation
2
Relamping Instructions
Contact Block Mounting