Bird Technologies 4275 Series - Manual

921-4273/75S Rev B Page 1 of 2
General
Models 4273 and 4275 are wide range adjustable Thruline® RF Couplers for signal observation on a scope or
frequency counter input. The output signal produced at the BNC output connector is an attenuated, unrectified
signal. They offer very low insertion VSWR across their frequency range and insertion loss is less than 0.2 dB.
The Model 4273 is a low frequency coupler for the 1.5 to 35 MHz band and offers a sample that ranges from 40
to 70 dB below the main power level. The Model 4275 covers a frequency band of 20 to 1000 MHz with an
attenuation range of 35 to 80 dB down from the main power. Both couplers have locking devices on their
attenuation control. Additional details on their performance characteristics are given under specifications.
Installation requires only that the coaxial cables have the mating connectors for the sampler. To obtain the
minimum insertion VSWR and loss, the N type connectors are preferred. Use an RF coaxial cable with a Male
BNC plug on one end to connect between the Female BNC port on the sampler and the scope or counter, All
versions on the models 4273 and 4275 are installed in an RF coaxial line through quick change “QC” connectors
except for the -100 models. These models are designed for direct mounting on any Bird device equipped with a
“QC” connector. Remove the “QC” connector from the device by unscrewing counterclockwise the four 8-32 x 5/
16 inch mounting screws. The -100 having no connectors of its own, is sandwiched between the “QC” connector
and the device. Place the “QC” connector on the female side of the sampler. Remount the “QC” connector and
sampler on the device by using the four 8-32 x 1-1/2 inch screws furnished with this sampler.
The operation of the variable samplers consists only of adjustment of the knurled coupling knob to obtain the
desired RF signal level a the BNC output port. The maximum output is obtained by screwing the knob
clockwise all the way in. The control shank threads have a special nonstrip provision when the knob is
screwed counterclockwise all the way out. To re-engage the threads, push the knob in gently and turn
clockwise. A locking lever is provided to prevent the chosen setting from being inadvertently disturbed.
Since the signal sampler is a passive device, it requires no external source of power or utility service.
Therefore, the unit cannot be turned off. The source of RF energy must be shut off instead.
These signal samplers are essentially very rugged and mechanically simple by design. They require very little
maintenance other than keeping them clean. Wipe the housing off occasionally with a clean dry cloth. In the
same way, wipe off the two “QC” connectors and the BNC port. Use a self-drying and nonresidue forming
aerosol contact cleaner on their inaccessible internal surfaces. Check the “QC” connectors from time to time to
be sure they are tightly and firmly mounted.
Other than replacing the “QC” connectors, there are no field repairs possible with the Models 4273 and 4275
Signal Samplers. Any other malfunction will require returning the sample to Bird Electronic Corp. for service.
To ship one of these samplers, screw the adjustment knob all the way in and lock it in place with the locking
lever. Wrap it carefully in padding and place it in a suitably sized corrugated paper box. Storage involves only
covering the device to keep off the dust and maintaining the ambient temperature between -40° and +45°C
(-40°F and +113°F).
There are no replacement parts for Models 4273 or 4275 except for the “QC” connectors. Listed below are
models equipped with suggested “QC” connectors.
CAUTION
Never attempt to disconnect the sampler from the transmission
line while RF power is being applied. Leaking RF energy is a
potential health hazard.
Instruction Sheet
Variable RF Sampler
Series 4273/75
Thruline® is a registered trademark of Bird Electronic Corporation