Blizzard Lighting Quadra ROCKLITE (Rev A) - Manual (Page 6)

Page 11
ROCKLITE Quadra Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Control Panel Menu Structure
Addr
<ENTER>
d001 - d512
<UP/DOWN/ENTER>
SLAV
<ENTER>
SL-U
<ENTER>
CHnd
<ENTER>
8CH
<UP/DOWN/ENTER>
5CH
4CH
3CH
SouA
<ENTER>
So-A
<ENTER>
SP--
<ENTER>
SP00- SP15
<UP/DOWN/ENTER>
Pr--
<ENTER>
Pr00- Pr35
<UP/DOWN/ENTER>
ASC-
<ENTER>
AC00- AC15
<UP/DOWN/ENTER>
FAdE
<ENTER>
FA00- FA15
<UP/DOWN/ENTER>
FLAS
<ENTER>
FL00- FL15
<UP/DOWN/ENTER>
rL--
<ENTER>
r000- r255
<UP/DOWN/ENTER>
GL--
<ENTER>
G000- G255
<UP/DOWN/ENTER>
bL--
<ENTER>
b000- b255
<UP/DOWN/ENTER>
UL--
<ENTER>
U000- U255
<UP/DOWN/ENTER>
Page 12
ROCKLITE Quadra Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
DMX Mode
Allows the unit to be controlled by any universal DMX controller.
1.) The default mode for the fi xture is DMX, which appears as
d001
on the LED
Readout. To select a different DMX address, using the <MENU> button, select
Addr
,then hit <ENTER>. Use the <UP/DOWN> buttons to select the correct
address, then hit <ENTER> to confi rm.
Stand-Alone, Master/Slave, Sound Active Modes:
Allows a single or Master/Slaved units to run factory installed programs at user selectable
speeds.
1.) To set the fi xture in Flash/Fade mode, select
FLAS or FAdE
To confi rm, press the <ENTER> button.
2.) Now, select the fl ash or fade speed using <MENU> button to reach
SP--
,
then hit <ENTER>.
The display reads
SP15
(slowest) to
SP00
(fastest), then press the <EN-
TER> button to confi rm.
3.) To use the fi xture in automatic mode, select
ASC-
, then press the <EN-
TER> button to confi rm.
4.) Adjust the speed of the chase as above using
SP15
(slowest) to
SP00
(fastest) then press the <ENTER> button to confi rm.
5.) To set the fi xture as a slave unit, select
SLAV
, and hit <ENTER>. The unit
will display a fl ashing
SL-U
to indicate it is in slave mode.
Sound Acitve Mode:
1.) To use sound active mode, select
SouA
, then press the <ENTER> button
to confi rm.
Standalone (Program) Mode:
Allows a single unit to display a variety of colors and programs without a DMX controller.
1.) To set the fi xture in manual mode, select
Pr--
.
To confi rm, press the <ENTER> button.
2.) Now, select the program by using the <UP> and <DOWN> buttons to select
Pr00-Pr15
. To confi rm, press the <ENTER> button.
Manual Color Adjustment:
Allows the user to adjust the color balance of the fi xture. These settings are global, they
will effect all modes.
1.) Use the <MENU> and <UP/DOWN> button to select
rL--
(Red Level),
GL--
(Green Level),
bL--
(Blue Level) or
UL--
(White Level), then hit
<ENTER>.
2.) Using the <UP/DOWN> buttons, select the maximum level for each color
between
x000-x255
(000=off), then hit <ENTER> to confi rm.