Blomberg WNF 5380 WE - Manual (Page 13)

13 EN
display. The Child Lock does not allow any
change in the programmes and the selected
temperature, speed and auxiliary functions.
C Even if another programme is selected with the
Programme Selection knob while the Child Lock
is active, previously selected programme will
continue running.
To activate the Child Lock:
Press and hold 1 st and 2 nd Auxiliary Function buttons
for 3 seconds. The lights on the 1 st and 2 nd Auxiliary
Function buttons will flash, and "C03", "C02", "C01"
will appear on the display respectively while you keep
the buttons pressed for 3 seconds. Then, "Con"
will appear on the display indicating that the Child
Lock is activated. If you press any button or turn the
Programme Selection knob when the Child Lock is
active, same phrase will appear on the display. The
lights on the 1st and 2nd auxiliary function buttons
that are used to deactivate the Child Lock will blink
3 times.
To deactivate the Child Lock:
Press and hold 1 st and 2 nd auxiliary function buttons
for 3 seconds while any programme is running. The
lights on the 1 st and 2 nd Auxiliary Function buttons
will flash, and "C03", "C02", "C01" will appear on
the display respectively while you keep the buttons
pressed for 3 seconds. Then, "COFF" will appear
on the display indicating that the Child Lock is
deactivated.
C In addition to the method above, to deactivate
the Child Lock, switch the Programme Selection
knob to On / Off position when no programme is
running, and select another programme.
C Child Lock is not deactivated after power failures
or when the machine is unplugged.
C If you switch off the machine by pressing the On
/ Off button when the Child Lock is active and
the machine is running, then the child lock will
be deactivated.
Progress of programme
Progress of a running programme can be followed
from the Programme Follow-up indicator. At the
beginning of every programme step, the relevant
indicator light will turn on and light of the completed
step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make must
be in a step after the running programme step. If the
change is not compatible, relevant lights will flash for
3 times.
C If the machine does not pass to the spinning
step, Rinse Hold function might be active or the
automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the machine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
when the water level is unsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine
checks the level of the water inside. If the level is
suitable, Loading Door light illuminates steadily within
1-2 minutes and the loading door can be opened.
If the level is unsuitable, Loading Door light turns off
and the loading door cannot be opened. If you are
obliged to open the Loading Door while the Loading
Door light is off, you have to cancel the current
programme; see "Canceling the programme".
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine
to pause mode while a programme is running.
The light of the step which the machine is in starts
flashing in the Programme Follow-up indicator to
show that the machine has been switched to the
pause mode.
Also, when the loading door is ready to be opened,
Loading Door light will also illuminate continuously in
addition to the programme step light.
Changing the speed and temperature settings
for auxiliary functions
Depending on the step the programme has reached,
you may cancel or activate the auxiliary functions;
see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C If no change is allowed, the relevant light will
flash for 3 times.
Adding or taking out laundry
Press the Start / Pause button to switch the machine
to pause mode. The programme follow-up light of
the relevant step during which the machine was
switched into the pause mode will flash. Wait until
the Loading Door can be opened. Open the Loading
Door and add or take out the laundry. Close the
Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press
Start / Pause button to start the machine.
C The loading door will not open if the water
temperature in the machine is high or the water
level is above the door opening.
Canceling the programme
To cancel the programme, turn the Programme
Selection knob to select another programme.
Previous programme will be canceled. End /
Cancel light will flash continuously to notify that the
programme has been canceled.
Pump function is activated for 1-2 minutes regardless
of the programme step, and whether there is water
in the machine or not. After this period, your machine
will be ready to start with the first step of the new
programme.
C Depending on the step where the programme
was canceled in, you may have to put detergent
and softener again for the programme you have
selected anew.
C If you want to open the loading door after you
have cancelled the programme but it is not
possible to open the loading door since the
water level in the machine is above the loading
door opening, then turn the Programme