Blomberg WNF 7241 WE20 User Manual
Page 13
13
EN
the programme will turn on.
C
If no programme is started or no key is
pressed within 1 minute during programme
selection process, the machine will switch to
Pause mode and the illumination level of the
temperature, speed and loading door indicator
lights will decrease. Other indicator lights and
indicators will turn off. Once the Programme
Selection knob is rotated or any button is
pressed, indicator lights and indicators will turn
on again.
Child Lock
Use child lock function to prevent children from
tampering with the machine. Thus you can avoid
any changes in a running programme.
C
If the Programme Selection knob is rotated
when the child lock is active, the lights on the
1
st
and 2
nd
auxiliary function buttons will blink
3 times. The child lock does not allow any
change in the programmes and the selected
temperature, speed and auxiliary functions.
C
Even if another programme is selected with
the Programme Selection knob while the Child
Lock is active, previously selected programme
will continue running.
C
When the Child Lock is active and the
machine is running, you can switch the
machine to Pause mode without deactivating
the Child Lock by turning the Programme
Selection knob to On / Off position. When
you turn the Programme Selection knob
afterwards, the programme will resume.
To activate the Child Lock:
Press and hold 1
st
and 2
nd
Auxiliary Function
buttons for 3 seconds. The lights on the 1
st
and 2
nd
Auxiliary Function buttons will flash while you keep
the buttons pressed for 3 seconds.
To deactivate the Child Lock:
Press and hold 1
st
and 2
nd
auxiliary function buttons
for 3 seconds while any programme is running. The
lights on the 1
st
and 2
nd
Auxiliary Function buttons
will flash while you keep the buttons pressed for 3
seconds.
C
In addition to the method above, to deactivate
the Child Lock, switch the Programme
Selection knob to On / Off position when no
programme is running, and select another
programme.
C
When the power is restored after a power
failure or after your machine is unplugged
and plugged in again, the Child Lock will not
be deactivated when the machine resumes
operating.
Progress of programme
Progress of a running programme can be followed
from the Programme Follow-up indicator. At the
beginning of every programme step, the relevant
indicator light will turn on and light of the completed
step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make must
be in a step after the running programme step. If
the change is not compatible, relevant lights will
flash for 3 times.
C
If the machine does not pass to the spinning
step, Rinse Hold function might be active
or the automatic unbalanced load detection
system might be activated due to the
unbalanced distribution of the laundry in the
machine.
Loading door lock
There is a locking system on the loading door of
the machine that prevents opening of the door in
cases when the water level is unsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine
checks the level of the water inside. If the level is
suitable, Loading Door light illuminates steadily
within 1-2 minutes and the loading door can be
opened.
If the level is unsuitable, Loading Door light turns
off and the loading door cannot be opened. If
you are obliged to open the Loading Door while
the Loading Door light is off, you have to cancel
the current programme; see "Canceling the
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the
machine to pause mode while a programme is
running. The light of the step which the machine
is in starts flashing in the Programme Follow-up
indicator to show that the machine has been
switched to the pause mode.
Also, when the loading door is ready to be opened,
Loading Door light will also illuminate continuously
in addition to the programme step light.
Changing the speed and temperature
settings for auxiliary functions
Depending on the step the programme has
reached, you may cancel or activate the auxiliary
functions; see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C
If no change is allowed, the relevant light will
flash for 3 times.
Adding or taking out laundry
Press the Start / Pause button to switch the
machine to pause mode. The programme follow-
up light of the relevant step during which the
machine was switched into the pause mode will
flash.
Wait until the Loading Door can be opened. Open
the Loading Door and add or take out the laundry.
Close the Loading Door. Make changes in auxiliary
functions, temperature and speed settings if
necessary. Press Start / Pause button to start the
machine.
Canceling the programme
To cancel the programme, turn the Programme
Selection knob to select another programme.
Previous programme will be canceled. End /