Cozzia 16018 - Manual

3
4
5
6
7
8
10
Chair Components 02
Chair Installing 03
06
04
Step 1:
Ensure sufficient space around chair, please leave 60cm of space behind the
backrest and 60cm of space at the front of the massage chair when reclining
backrest and elevating leg rest.
Step 2:
Unfold the Backrest
Remark: If you want to fold the Backrest, lift the stopper as shown in picture.
Then fold the Backrest onto the seat.
at least 60cm at least 60cm
RELAX
DUAL-ACTION
ROLLING
SWIDISH
AIR
INTENSITY
WIDTH
THERAPY
L M H
H L M H L M
KNEADING SPOT
TAPPING
PARTIAL
MASSAGING POSITION
Moving the chair
Side Panel
Wheels
Backrest
Spare pad
Roller
Remote Controller
Step 3:
Installing the Remote Control Holder
Please tighten the screws of the Remote Control Holder
in the order of the picture shown.
Step 4:
Back Massage Strength-Control Pad
Back Massage Strength-Control Pad has been into the Backrest Cover.
If a stronger massage is desired, remove the Back Massage Strength-Control Pad
from the back by zipping the cover off the back pad (as shown in picture). If a milder
massage is desired, return the Back Massage Strength-Control Pad to the cover.
1. Elevate the Calves Rest.
2. Then recline the chair to approx. 45°to move the chair around the house with a
slight pull of push.
Note:
• Always return the leg rest to its original length before moving the chair.
Otherwise, it may result in injury during movement.
• Do not move the unit while a person is seated on it.
• Place a mat on the floor and gently roll the unit over it to void damaging the floor.
11
Operation Guide
Insert the power cord plug into the suitable electrical, and turn the power switch to
‘’I” position, and the chair automatically enters the idle mode. During the idle mode,
only five functions are available: “ ON/OFF, Recline Backrest, Elevate Leg rest or
Recline Leg rest ”.
CONTROL BUTTONS FOR THE MASSAGE CHAIR
1. ON/OFF
The start/ Stop control Button
Press once on this button; the massage chair is in idle mode, press any massage
function to begin massage function on the chair.
Press this button again to stop all massage functions, the massage rollers will
return to its original position.
2. Raise Leg Rest/Recline Backrest
Angle adjustment control button for massage chair
This control button allows raising leg rest and reclining backrest synchronously.
Press once to adjust the chair to a comfortable position, then press again to confirm
the position.
3. Recline Leg Rest /Raise Backrest
Angle adjustment control button for massage chair
This control button allows reclining leg rest/raising backrest synchronously. Press
once to adjust the chair to comfortable position, then press again to confirm the
position.
12
AUTO PROGRAM
Three Auto Programs are available and you can choose the desired one by
pressing these corresponding buttons.
4. Relax
5. Therapy
6. Air
Note: All three Auto Programs cannot be combined.
MANUAL BACK MASSAGE PROGRAMMING
7. Kneading
Kneading Function Start/Stop Control Button-3 levels of intensities
Press once to activate the Kneading function for full back massage at medium
intensity, and then press again to stop the Kneading massage function. Also the
kneading intensity can be adjusted by pressing the “Intensity” button after
activating the kneading function.
8. Tapping
Tapping Function Start/Stop Control Button - 3 sizes of width and 3 levels of
intensities
Press once to activate the Tapping function for full back massage at medium width
and intensity, then press again to stop the tapping massage function. Also the
tapping width and intensity can be adjusted by pressing “Width” and “Intensity”
button respectively after activating tapping function.
9. Dual-Action
Dual-Action Function Start/Stop Control Button-3 levels of intensities
Press once to activate the Dual-Action function for full back massage at medium
intensity, then press again to stop function. Also the Dual-Action intensity can be
adjusted by pressing the “Intensity” button after activating Dual-Action function.
13
10. Swedish
Swedish Function Start/Stop Control Button-3 levels of intensities
Press once to activate the Swedish function for full back massage at medium
intensity, then press again to stop function. Also the Swedish intensity can be
adjusted by pressing the “Intensity” button after activating Swedish function.
11. Rolling
Rolling Function Start/Stop Control Button - 3 sizes of width and 3 levels of
intensities
Press once to activate the Rolling function for full back massage at medium width
and intensity, press again to stop it. Also the tapping width and intensity can be
adjusted by pressing “Width” and “Intensity” button respectively after activating
tapping function.
Note: Kneading/Tapping/Dual-Action/Rolling cannot be combined.
SETTING SPOT OR LOCALISED BACK MASSAGES
12. Spot
Spot Back Massage
This button allows users to select Spot massage for any part on the back by
pressing button to user’s desired position. Press this button once, the massage
rollers run at the original position in original massage mode. Press again to cease
Spot massage function and resume full back massage function.
Note: The Spot massage cannot be operable during the Rolling function.
13. Partial
Partial Back Massage
This button allows users to select Partial massage for any part on the back by
pressing button to user’s desired position. Press this button once, the massage
rollers run at the original position in original massage mode. Meanwhile, the
massage rollers will take the original position as the centre to perform Partial
Massage with the width of approx. 8 cm within movement range of rollers. Press
again to stop Partial massage function and resume full back massage function.
14
14. ▲/▼
Position Adjustment Button for Spot or Partial Massage
After activating Spot or Partial Massage, continue to press the buttons in
succession to move the massage rollers. The massage rollers will go upwards or
downwards until the desired position. The original position of the Spot pr Partial
massage will be shifted to the new position. Release the button once the desired
position is achieved.
15. Width
Width Adjustment Button for Tapping and Rolling Function
After activating the Tapping and Rolling function, every time the button is pressed,
the width can be adjusted in the sequence of “mode2<mode 3< mode1”.
16. Intensity
Intensity Adjustment button for Kneading, Tapping, Dual-Action and Auto
Program mode.
After activating the Kneading, Tapping, Dual-Action and Auto Program function,
every time the button is pressed, the intensity can be adjusted in
the sequence of “mode 2<mode3<mode1”.
SETTING AIR SQUEEZE
17. Seat
Seat Air Squeeze and Vibration Control Button
Press this button to activate the Air Squeeze and Vibration function in the seat,
press again to stop the function.
18. Calves
Calves Air Squeeze Control Button
Press this button to activate the Air Squeeze function in the calves, every time the
Calves button is pressed, the Calves Air Squeeze function will be changed in the
sequence of “mode2<mode3<mode1<off<mode 2”.
15
19. Feet
Feet Air Squeeze Control Button
Press this button to activate the Air Squeeze function in the feet, every time the Feet
button is pressed, the Feet Air Squeeze function will be changed in the sequence of
“mode2<mode3<mode1<off<mode 2”.
Remark: Vibration and Air Squeeze function can be combined with Kneading,
Tapping, Dual-Action and Rolling to enjoy multi-massage functions.
20. Pause
Pause Button
When the chair is in massage mode and the user wants to pause it temporarily,
press this button and all massage functions will stop. The backlight of the original
massage button is still activated. The chair is now into idle mode, only the “Pause,
ON/OFF, Recline, Raise, Elevate Leg Rest, Recline Leg Rest” buttons can be used.
Press the Pause button again to resume the original massage function.
COMPLETING THE MASSAGE
Press the ON/OFF button to stop the massage operation. Massage Rollers will
resume its originally specified position, then switch the power button under the chair
to “0” position and disconnect the power cord plug from the electrical outlet.
● Please consult your doctor if you are in doubt as to whether or not you should
use this massage chair.
● Please consult a doctor before using the massage chair if you are pregnant,
undergoing any medical treatment, using a medical electronic device such as
a pacemaker, or are experiencing any of the following: Malignant tumor, heart
disease, back pain, abnormal or curved back bone, osteoporosis or acute illness.
● If you experience pain while using the massage chair, stop using it immediately
and consult your doctor.
● Never use a massage function on swollen or inflamed parts of the body.
● DO NOT use the massage chair for more than 30 minutes at a time.
● DO NOT use the massage chair where aerosol (spray) products are being used
or where oxygen is being administered.
● This massage chair is a non-professional product designed to provide a
comfortable massage and should not be substituted for appropriate medical
treatment.
● If the supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
2
Safety Precautions 01
When using the massage chair, basic precautions should always be followed to
reduce the risk of electric shock, burns, fire or injury to persons. Please read the
following precautions before using the massage chair.
● Make sure the power plug is securely inserted into a proper electrical outlet to
reduce the risk of short-circuit and fire.
● Always unplug the massage chair from the electrical outlet immediately after
using and before cleaning.
● DO NOT use the massage chair in areas where the humidity is high such as a
sauna or steam room.
● DO NOT use the massage chair outdoors and avoid areas with direct sunlight.
● If the electricity is off, turn the power switch to the OFF position and unplug the
massage chair form the electrical outlet to prevent any damages to your chair
when the electricity comes back on.
● Never plug/unplug the power cord plug socket with wet hands.
● Close and continuous supervision is necessary when the massage chair is used
by, on or near children or disabled persons.
● No more than one person should use the massage chair at a time.
● The massage chair is intended to be used as described in the Instruction Manual.
Do not use any attachments other than those recommended.
● DO NOT attempt to stand or sit on the backrest or footrest in order to prevent
accident, injury or damage to the chair.
● Avoid falling asleep while using the massage chair.
● Always keep the massage chair clean, and never insert any objects into or
around the gaps of the massage chair.
● DO NOT move the massage chair by pulling on the power supply cord.
● Make sure there are no children, pets or other obstacles behind or underneath
the massage chair.
● If you find any rips or tears in the fabric of the massage chair contact our service
department.
● This massage chair is designed for household use and should not be used in
non-residential settings.
1
Table of Contents
Thank you for purchasing the EC-362B Massage Chair.
Before using your massage chair, please read the contents of this
instruction manual and refer to it when needed.
Safety Precautions ………………………..…………… 2 - 3
Components of the Chair …………………….......…… 4 - 5
Chair Installing …………………………………….....… 6 - 7
Moving the Chair ……………………………………..… 8
Grounding Instructions ……………………...........…… 9
Operation Guide ……………………………………...… 10 - 15
Features ……………………………………...............… 16
Troubleshooting ………………………………...……… 17
Warnings ………………………….....…....................… 18
Consumer Warranty ……………………..............….… 19-21
Warranty Card (Attachment)
16
07
The operation of Massage Chair is controlled by a microcomputer that performs
various intelligent massage methods and combinations like Kneading, Tapping,
Rolling and Air Massage. All these methods massage the acupressure points to
accurately and effectively alleviate fatigue, promote metabolism and improve
blood circulation.
1. Designed with rest length adjustment for a more comfortable leg position
combined with various types of massage function to achieve more effective
massage.
2. Massage angle can be adjusted according to the user’s need and more
effective massage.
3. Unique air squeeze design for the seat, foot and calves make the massages
more effective.
4. User friendly Controller for ease of operation.
5. The ergonomic design of the massage chair is the result of dedicated research
to create the best massage solution.
Features
17
Troubleshooting 08
This massage chair is controlled by a microcomputer and is susceptible to power
surge even by +10% or -15%. The massage chair will show the following strange
circumstances:
1. In the auto timing mode, when the
timing is appropriate, repress the
power switch.
2. Switch power OFF and ON again
to activate the Chair.
1. Check whether the plug is well
connected and working.
2. Check whether the switch on the
Massager Chair is turned to
“I” position.
The Massage Chair operates even
though it has been connected to
the power supply.
During operation, the Controller is
working but not the Massage Chair.
The Massage Chair could be
overheated after prolonged use. It will
automatically cool down to resume its
normal condition. Please turn off the
power and allow the Chair to cool off
for 30 to 50 minutes.
During operation, both Controller
and the Massager Chair are not
working.
Situation Solution
9
Grounding Instructions 05
Fully insert the plug into an appropriate outlet.
An improper equipment-grounding conductor may result in electric shock. Contact
a qualified electrician if you are not sure that the product is properly grounded.
Do not modify the plug that is included with the massage chair.
If the plug does not fit the outlet, contact a qualified electrician to install an outlet to
fit the massage chair plug.
18
09
* Do not use water and other cleaning detergents on the massage chair.
* Do not stack, stab, slit or harshly pull on the surface of the massage chair.
* Gently press the buttons during operation and avoid hitting the buttons with
hard objects.
* Pull out the power supply plug after each use.
* Do not use the massage chair for more than 30 minutes at a time.
Warnings
Instruction Manual EC-362B
21
20
19
10 COZZIA Consumer Warranty
COZZIA products have the following warranty: COZZIA’s massage chairs,
motion upholstery and home theater massage seating provide a one year in-home
service warranty and a two-year parts warranty. COZZIA customer service will not
issue Return Material Authorizations (RMAs) for products. COZZIA products will be
either repaired by the consumer or by an in-home technician. COZZIA will not issue
Return Material Authorizations (RMAs) for buyer’s remorse.
SERVICE AND TECHNICAL SUPPORT
Consumers may contact COZZIA’s customer service department at 1-877-977-0656
between 9:00 am and 5:00 pm PST, Monday through Friday or email us at
[email protected] or visit our web at www.cozzia-usa.com for warranty or
service issues.
Consumers are required to provide the unit serial number and dated proof of
purchase (sales receipt) when they contact the COZZIA service department
regarding a repair.
A COZZIA customer service representative will attend to most consumer inquiries,
but in some cases a technical service specialist will provide advanced support.
Non-warranty repair is provided on a "per incident" basis. COZZIA customer service
will verify that the unit has failed and provide instructions for repairing a unit. All
applicable repairs, parts, shipping, handling, local tax and a "per incident" fee will be
charged for non-warranty repairs and support calls.
Proof of purchase (original receipt) is required for all warranty repairs or service.
EXTENDED WARRANTIES:
Cozzia offers extended warranty programs to enhance ownership of Cozzia
product. Extended warranty provides: 3-year limited repair or replacement massage
chair warranty with on-site service.
Please visit www.cozzia-usa.com for the latest terms and pricing for extended
warranties.
● Floor Models and Demonstration Units have a prorated warranty period
that begins the day the model is placed on the floor and connected to an
electrical outlet by the retail partner. Proof of purchase is required in order
to obtain warranty service and parts. Non-warranty parts and service are
available at a “per incident” charge.
●
Warranty Coverage Period - Warranty coverage starts at the time that the
consumer PURCHASES their chair. Proof of purchase is required for all
warranty repairs. The warranty time period is measured by continuous
calendar days based on a seven-day week.
●
Field Service – COZZIA customer service department will diagnose and
schedule an authorized service provider to repair the chair in the
consumer's residence.
●
Parts - All parts deemed necessary for repairs will be shipped to the
consumer at no charge by the COZZIA service department.
PRODUCT REPAIRS
Many COZZIA product repairs may be performed by the consumer in their own home
with parts and instructions supplied by COZZIA such as remote controller
replacements that don’t require a technician.
Canadian consumers may contact COZZIA's customer service department at
1-877-977-0656 between 9:00 am and 5:00 pm PST, Monday through Friday for
warranty or service issues.
CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS
● Warranties are only valid in the 48 contiguous United States and Canada
and are contingent upon the consumer operating the chair according to the
corresponding instruction manual.
● The warranty only applies to COZZIA products and does not include any
accessories or enhancements.
● Field service requires pre-approval and must be performed by COZZIA’s
authorized field service personnel. Field service is only available in the
United States and in major metropolitan areas in Canada.
● Softening of foams and filling composites in pillows, pads, and memory
foam occurs naturally and does not constitute a defect under this warranty.
● Fading, wear and piling of fabrics occurs naturally and does not constitute
a defect under this warranty.
● Natural markings, grain and dye variations in leather do not constitute a
defect under this warranty.
● Warranties do not cover any loss or damage resulting from improper
installation, unauthorized repairs or modifications, improper use of
electrical/power supply, loss of power, dropped product, a malfunction or
damage of an operating part from failure to provide manufacturer's
recommended maintenance, transportation damage, theft, abuse, misuse,
neglect, vandalism or environmental conditions (fire, floods, rust, corrosion,
sand, dirt, windstorm, hail, earthquake or exposure to weather conditions),
loss of use during the period the product is at a repair facility, or otherwise
awaiting parts or repair.
● Damage due to shipping and handling does not constitute a defect under
this warranty.
● Under no circumstance shall COZZIA or its representatives be liable for
indirect, consequential, or incidental damages (including damages for lost
profits, business interruption, bodily injury, medical and the like), even if
any party has been advised of the possibility of such damages.
● Warranties are non-transferable and shall be in lieu of any other warranty,
express or implied, including but not limited to any implied warranty or
merchantability or fitness for particular use.
● COZZIA’s sole liability and the purchaser's exclusive remedy shall be for
the repair, or at COZZIA’s option, for the replacement of the defective part.
Not withstanding the above, if replacements parts for defective materials
are not available, COZZIA reserves the right to make substitutions in lieu
of repair or replacement.
● All warranties begin on the DATE OF PURCHASE; no allowance or
extension is offered for delivery and/or installation.
● Warranties do not apply to rental, business, commercial, institutional or
other non-residential users.
Product Serial No. (located on product):
Purchase Price: Model No:
Date Purchased:
First Name: Last Name:
Address:
City: State: Zip:
Phone:
Email:
Please mail to:
Cozzia USA LLC
14251 E Don Julian Rd
City Of Industry CA 91710
Tel: 1-877-977-0656
Fax: 1-800-521-4712
WARRANTY REGISTRATION FORM
Warranty Card