E-flite 20-Amp Mini Brushed ESC with Brake - Manual

Thank you for choosing the E-flite ™ brand. Your
satisfaction is our number one priority. With this in
mind, we have produced this product to be of the
highest quality, performance, and reliability at a
“value-packed” price. We hope it provides you with
hours of enjoyment.
• Thermal overload/current protection
(prevent ESC burnout if overloaded or shorted)
• Auto-cutoff shuts off power to the motor while
still supplying power to operate the radio
• 20-amp continuous current
• Input Voltage Range: 5-cell, 6-volt to 10-cell, 12-volt
• BEC Voltage: 3.6 volts DC, 1 amp
• Prewired with Tamiya battery connector and
bullet-style motor connector
• Universal receiver plug
• On/Off switch
Operation: Proportional forward
power, with brake, auto-
cutoff
Input Voltage: 5-cell (6 volts) through
10-cell (12 volts)
Continuous Current: 20 amps
Size: (1.14" x .68" x .26")
29mm x 17mm x 6.6mm
Weight: .63 ounces (17.8g)
A universal receiver connector is prewired to the
controller (see diagram). Insert the receiver
connector into the throttle channel of the receiver.
This connector is compatible with JR, Futaba and
Hi-Tec receivers. Other types of receivers may not be
compatible. Be sure to route the receiver connector
wire neatly.
The E-flite Speed Controller will handle continuous
current up to 20 amps. This typically includes up to
Speed 400 motors. Female bullet-style connectors
are provided for convenient hookup with motors
that are prewired. The red wire is positive (+) and
the black wire is negative (-).
The E-flite 20-amp Speed Control comes prewired
with a Tamiya style battery connector that is
compatible with connectors found on most battery
packs. You can use a 5-cell to 10-cell battery
pack (6- to 12-volt).
Using double-sided servo tape, mount the E-flite
20-Amp Speed Controller in the position shown in
the instruction manual for your particular model. Be
sure to mount the control so that the motor, battery,
and receiver wires reach. Mount the switch using a
screw and switchplate kit or use double-sided servo
tape on the side of the switch to mount it to the
fuselage of your model.
1. Be sure the On/Off switch is in the off position
and the motor is not yet connected.
2. Plug the speed control throttle lead into the
throttle servo receptacle on the receiver.
3. You must first properly set up the transmitter.
Turn on the transmitter and place the throttle
control stick in the center position. If you have
a computer transmitter, adjust the throttle ATV
to 100%.
4. Connect a fully charged battery to the battery
connector on the speed control. Note the
positive and negative leads. Ensure proper
polarity when making the connection, because
incorrect polarity will damage the speed control.
5. If you used a PCM transmitter, set the fail-safe
memory on low speed.
6. Turn off all switches before connecting the
motor. After connecting the motor, turn the
switches on. The throttle will start from
low speed.
7. Test the motor.
Note: If your electronic speed control fails to
operate after following the above steps,
unplug the receiver connector and rotate 180˚.
To receive warranty service, your original dated sales
receipt must be included to verify your proof-of-
purchase date. Providing warranty conditions have
been met, your electronic speed control will be
repaired or replaced free of charge.
Should your repair cost exceed 50% of the retail
purchase price, you will be provided with an
estimate, advising you of your options. Any return
freight for non-warranty repairs will be billed to
the customer.
For non-warranty repairs, please advise the
payment option you prefer to use. Specify VISA,
Mastercard or money order. If you choose to use
a credit card please include your card number and
expiration date.
E-flite 20-Amp 120-Day Limited Warranty
E-flite warranties this product to be free from
defects in materials and workmanship for a period
of 120 days from the original date of purchase.
It is limited to the original purchaser of this
electronic speed control and is not transferable.
This warranty will not cover units that have been
modified, misused, or serviced by an unauthorized
service center.
Your warranty may be voided if damage
results from:
1. Reverse voltage is applied to your E-flite
20-Amp Speed Control (e.g., connecting
battery pack backward, plugging battery into
the motor connector wires, etc)
2. The battery plugs or connectors are altered or
removed
3. You allow your wires to become frayed or shorted
4. Use of less than 5-cell (6 volts) or more than a
10-cell (12 volts) battery pack
5. Tampering with any of the electronic components
6. Allowing water, moisture, or foreign material
(e.g. dirt, dust, etc.) into the electronic speed
control unit
Under no circumstances will the buyer be entitled to
consequential or incidental damages. This limited
warranty gives you specific legal rights; you also
have other rights that may vary from state to state.
If your electronic speed control is in need of repair,
please ship it freight prepaid to:
Horizon Service Center
ATTN: E-flite Service
4105 Fieldstone Road
Champaign, Illinois 61822
(217) 355-9511
Include your complete name and address
information inside the carton, as well as write it
clearly on the return address label area. Include a
brief summary of the difficulty. Date your
correspondence and be sure your name and address
appear on this enclosure. Also, include a phone
number where you can be reached during the
business day.
Features
Diagram
Mounting the Controller
Hooking Up the Motor
Warranty Repairs
Non-Warranty Repairs
Warranty Information Preflight Instructions
Specifications
EFLA105
20-Amp
Mini ESC
with Brake
Instruction Manual
-
+
Connect to
Throttle
Channel
Power Switch
Motor
Ni-Cd Battery Pack
BEC-Type Connector
Receiver
Hooking Up the Receiver
Hooking Up the Speed Control
™
© 2002 Horizon Hobby, Inc.