K-array KZ12 - Manual (Page 2)

1
1
Input from
amplifier
2.Connect the cable to the device
Wall bracket
INSTALLATION
2
2
2 2
2 2
1
1
Fixing points
for wall bracket
2
1
MADE IN ITALY
IN+
IN-
Lyzard KZ12
www.k-array.com
KZ10W
1.Fix the bracket to the mounting surface using the
screws and wall anchors included.
3.Use the included screws to fix the device
to the positioned bracket
4.Bend the bracket to the desired angle.
SERVICE
A - Solder the cable on
terminals , in+ in-
B - press the cable with isolated
silicone screws on terminals , in+ in-
OR
ceiling
table
wall wall
K-array s.u.r.l.
Via Paolina Romagnoli 17
50037 San Piero a Sieve (Firenze)- Italy
tel +39 055 8487222
tel +39 055 8487238
e-mail: [email protected]
www.k-array.com
K
array
Acoustics
8 w(AES) Speaker power handling
350 Hz - 18 KHz +/- 3dB Operating frequency range
95 dB continuous - 102 dB peak Maximum SPL
Physical
2.1 x 10 x 1.2 cm (0.83 x 3.94 x 0.47 inches) Dimensions
46g (0.10 lbs) Weight
Coverage
140° Horizontal
20° Vertical
Cross over
External crossover required Type
250Hz 24dB/oct minimum suggested Frequency
Transducers
4 x 0.5" Neodymium speaker with 0.5" voice coil Full range
Impedance 16
To obtain service:
1) Contact the official K-array distributor in your country. Your local distributor will direct you to
the appropriate service center.
2) If you are calling for service, please have the serial number(s) of the unit(s) available for
reference. Ask for Customer Service, and be prepared to describe the problem clearly and
completely.
3) If the problem cannot be resolved over the phone, you may be required to send the unit in for
service. In this instance, you will be provided with an RA (Return Authorization) number which
should be included on all shipping documents and correspondence regarding the repair. Shipping
charges are the responsibility of the purchaser.
Any attempt to modify or replace components of the device will invalidate your warranty. Service
must be performed by an authorized K-array service center.
Cleaning:
Use only a soft, dry cloth to clean the
housing. Do not use any solvents,
chemicals, or cleaning solutions
containing alcohol, ammonia, or
abrasives. Do not use any sprays near
the product or allow liquids to spill
into any openings.
1
1
Input from
amplifier
2.Connect the cable to the device
Wall bracket
INSTALLATION
2
2
2 2
2 2
1
1
Fixing points
for wall bracket
2
1
MADE IN ITALY
IN+
IN-
Lyzard KZ12
www.k-array.com
KZ10W
1.Fix the bracket to the mounting surface using the
screws and wall anchors included.
3.Use the included screws to fix the device
to the positioned bracket
4.Bend the bracket to the desired angle.
SERVICE
A - Solder the cable on
terminals , in+ in-
B - press the cable with isolated
silicone screws on terminals , in+ in-
OR
ceiling
table
wall wall
K-array s.u.r.l.
Via Paolina Romagnoli 17
50037 San Piero a Sieve (Firenze)- Italy
tel +39 055 8487222
tel +39 055 8487238
e-mail: [email protected]
www.k-array.com
K
array
Acoustics
8 w(AES) Speaker power handling
350 Hz - 18 KHz +/- 3dB Operating frequency range
95 dB continuous - 102 dB peak Maximum SPL
Physical
2.1 x 10 x 1.2 cm (0.83 x 3.94 x 0.47 inches) Dimensions
46g (0.10 lbs) Weight
Coverage
140° Horizontal
20° Vertical
Cross over
External crossover required Type
250Hz 24dB/oct minimum suggested Frequency
Transducers
4 x 0.5" Neodymium speaker with 0.5" voice coil Full range
Impedance 16
To obtain service:
1) Contact the official K-array distributor in your country. Your local distributor will direct you to
the appropriate service center.
2) If you are calling for service, please have the serial number(s) of the unit(s) available for
reference. Ask for Customer Service, and be prepared to describe the problem clearly and
completely.
3) If the problem cannot be resolved over the phone, you may be required to send the unit in for
service. In this instance, you will be provided with an RA (Return Authorization) number which
should be included on all shipping documents and correspondence regarding the repair. Shipping
charges are the responsibility of the purchaser.
Any attempt to modify or replace components of the device will invalidate your warranty. Service
must be performed by an authorized K-array service center.
Cleaning:
Use only a soft, dry cloth to clean the
housing. Do not use any solvents,
chemicals, or cleaning solutions
containing alcohol, ammonia, or
abrasives. Do not use any sprays near
the product or allow liquids to spill
into any openings.