Krell Phantom III - Manual (Page 2)

2 Krell Phantom III Krell Phantom III 3
Figure 1 The Phantom III Front Panel
Figure 2 The
Phantom III
Remote Control
Figure 3 The Phantom III Back Panel
This product is manufactured in the United States of America. Krell ® is a registered trademark of Krell Industries, LLC., and is restricted for
use by Krell Industries, LLC. its subsidiaries, and authorized agents. Krell Current Mode™ and Evolution CAST™ are trademarks of Krell
Industries, LLC. All other trademarks and trade names are registered to their respective companies.
© 2012 by Krell Industries, LLC., All rights reserved.
Front Panel 11 Balanced inputs: B-1
and B-2
These XLR balanced
analog source input
connectors are wired
as follows:
Pin 1 Ground
Pin 2 Non-inverting
Pin 3 Inverting
12 Single-ended inputs:
S-1, S-2, and S-3
There are 3 single-
ended analog source
inputs with RCA con-
nector pairs.
13 Main outputs
The Phantom III is
equipped with one bal-
anced XLR output pair
and one single-ended
RCA output pair.
Customizing
the
Phantom III
1 Power
Use this to switch the
preamplifier between
stand-by and opera-
tional modes.
2 Display
This provides channel
status messages, in-
cluding input selection,
volume level, balance
offset, and menu selec-
tions.
3 Infrared sensor
This receives com-
mands from the remote
control. Make sure this
is not obstructed.
4 Stand-by/Power LED
This preamplifier LED
illuminates red (stand-
by) when the Phantom
III is plugged into a stan-
dard AC wall receptacle
and rear power switch is
on. The LED illuminates
blue (operational mode)
when the power button
(1) is pressed while the
Phantom III is in stand-
by mode.
5 Analog Input selectors
Use these to select
the corresponding
rear panel input that is
connected to a single-
ended (S-1, S-2, S-3), or
balanced (B-1, B-2) ana-
log source. The display
(2) shows the selected
input and volume level.
Pressing the input but-
ton on the active source
will mute all outputs.
A second press will
unmute the outputs.
6 Digital Input selec-
tor (functional with
optional D/A converter
module)
Use this to select the
D/A converter module.
Pressing and holding
the digital button will
cycle through the addi-
tional digital inputs.
7 Headphone Jack
1/4" stereo headphone
jack. The main outputs
are muted when head-
phones are being used.
8 Enter button
Use this to configure the
menu functions of the
Phantom III. See menu
(9).
9 Menu button
Use this to access the
menu functions of the
Phantom III. For
more information,
see
Customizing the
Phantom III, in the
owner’s reference.
10 Level control knob
Use this knob to
increase or decrease
system volume level.
The level control knob
or keys also select
menu options that cus-
tomize the Phantom III.
14 RS-232 port
This port receives mes-
sages from a computer-
based control system,
providing integrated
control of all preamplifier
functions. For details,
see the developer's
reference:
RS-232 Port:
Sending Commands
and Interpreting Data.
15 RC-5 in
This remote connector
is used with third-party
remote control systems
that provide RC-5 (IR)
data via a wired con-
nection. A stereo tip,
ring, sleeve 1/8” mini
connector is used in the
following configuration:
Tip = RC-5 data
Ring = +5 V
Sleeve = GND.
Configurable
Functions
AC Mains
Balance (channel)
Balance (input trim)
Display, Info
Input Level Trim
Input Name, Input Phase
Input Trigger, Mute,
Output Trigger, Recall,
Save, Theater.
The menu button or key
(9) allows you to configure
functions. Enter the menu
to view the list of configu-
rable functions.
Select a function to view
a submenu of the list of
options that configure the
function. You can configure
some options as well, if a
second submenu appears
when you select an option.
Navigation
Conventions
Navigating the preamplifier
menu is straightforward and
consistent throughout, using
4 functions and the menu
option BACK.
9 Menu Button or Key
To enter the menu,
press the menu button
or key. Once you are
in the menu, you can
press the menu button
or key to exit the menu.
10 Level Control Knob
or Up and Down Keys
Use the level control
knob or the up and
down keys on the re-
mote control to scroll
forward and backward
through the menu hier-
archy. Each menu list is
a continuous loop.
For more information on
menu configuration, review
the Owner’s Reference on
the Krell website at www.
krellonline.com. Navigate to
Downloads/ Current, then
select the Phantom III from
the product list. The publi-
cation list for the Phantom
III appears. 8 Enter Button or Key
Press this button or key
to select a function or
a configuration option,
and confirm a selection
3 Front Panel Display
The display shows the
active function and con-
figurable options.
BACK
Select
BACK to scroll
backwards through
the menu hierarchy, or
to exit a menu option
without confirming that
option.
16 12 VDC in/out
(12 V trigger)
There are 2 outputs and
one input that send and
receive 12 VDC power
on/off (trigger) signals
to and from other Krell
components, and other
devices that incor-
porate a 12 V trigger.
This allows other com-
ponents to be turned
on/off, or to/from stand-
by, through the remote
control.
For more information,
see Input Trigger in the
owner’s reference.
17 IEC power cord
receptacle and power
switch
This is for use with the
provided AC power
cord. Plug the other
end into an AC Mains
supply capable of sup-
plying the correct AC
voltage and current for
the power supply. This
connector and power
cord must remain
unobstructed for easy
removal in case of an
emergency.
18 Optional D/A
Converter Module
Location for future
plug in D/A converter
module.
Keys labeled 1 to 10
have the same function
(and callout number) as
the front panel controls.
Keys labeled A through
K are unique to the re-
mote control, and are
described below:
A Phase key
Inverts the polarity of
the audio signal. A
lowercase
i is displayed
when the polarity is
inverted.
B Mute key
Use this mute all out-
puts. A second press
of the mute key will
unmute the outputs.
C Sel(ect) key
Cycles through the digi-
tal inputs. This is only
active when the optional
D/A converter module is
installed.
D Bal(ance) keys
Use to balance left and
right output levels.
E Transport keys
These keys are func-
tional with all Krell CD
and DVD players.
F CD key
Press this to make the
transport keys operate
Krell CD players.
G Direction keys
Use these keys to
navigate CD and DVD
menus.
H Select Key
Use this to make selec-
tions from CD and DVD
menus.
I DVD key
Press this to make the
transport keys operate
DVD players.
J Menu key
Use this to enter CD or
DVD player menus.
K Title key
Use this with CD or
DVD player menus.
Note
The remote is shipped
with two AAA batteries
that have to be instal-
led. Use the supplied
Torx wrench to remove
the battery panel, then
install the batteries.
Remote
Control
Back Panel