Powers 205 Series TempTAP Lead Free Gooseneck Thermostatic Faucets - Cartridge Kit - Manual

IS-P-TempTap-CK
For Use with TempTAP ™ Models 105, 205, 115,
and 215
Installation Instructions
n
1. Turn hot and cold water supplies off.
2. Remove handle by unscrewing set screw with an allen wrench.
3. Remove shroud and high-temperature limit stop.
4. Unscrew bonnet nut and remove.
5. Pull cartridge out.
6. Replace cartridge. Make sure posts at the bottom of the car-
tridge match the holes in the body.
7. Install bonnet nut and high-temperature limit stop.
8. Turn hot and cold water supplies on.
9. Adjust the temperature as follows:
a. Loosen two high-temperature limit stop screws.
b. With the handle in place, rotate clockwise to desired outlet
temperature.
c. Remove handle and slide high-temperature limit stop on
inner bonnet ring, sliding it counterclockwise until it contacts
cartridge lever.
Note: Do not exceed temperature above 105°F (41°C).
d. Tighten high-temperature limit stop with two set screws.
10. Install shroud and handle.
11. Turn handle to maximum hot position and verify
temperature setting.
TempTAP
™
Cartridge Kit
IS-P-TempTap-CK 1024 EDP# 6512332 © 2010 Powers
USA: Phone: 1.800.669.5430 • Fax 1.847.229.0526 • www.powerscontrols.com
Canada: Phone: 1.888.208.8927 • Fax 1.888.479.2887 • www.powerscontrols.ca
Warranty n
The Seller warrants that the equipment manufactured by it and covered by this order or contract
is free from defects in material and workmanship and, without charge, equipment found to be
defective in material or workmanship will be repaired, or at Seller’s option replaced F.O.B. original
point of shipment, if written notice of failure is received by Seller within one (1) year after date
of shipment (unless specifically noted elsewhere), provided said equipment has been properly
installed, operated in accordance with the Seller’s instructions, and provided such defects are not
due to abuse or decomposition by chemical or galvanic action. ThiS expreSS warranTy iS in
lieu OF and excludeS all OTher warranTieS, guaranTeeS, Or repreSenTaTiOnS,
expreSS OF implied. There are nO implied warranTieS OF merchanTaBiliTy Or OF FiT-
neSS FOr a parTicular purpOSe. The Seller assumes no responsibility for repairs made on
the Seller’s equipment unless done by the Seller’s authorized personnel, or by written authority
from the Seller. The Seller makes no guarantee with respect to material not manufactured by it.
A Watts Water Technologies Company
Garantía n
el Vendedor garantiza que los equipos fabricados por él y cubiertos por esta orden o contrato
están libres de defectos en los materiales y mano de obra y que los equipos con materiales o
mano de obra defectuosos serán reparados sin cargo o, a opción del Vendedor, reemplazados
F.O.B. en el punto original de envío, si el Vendedor recibe una notificación por escrito de falla en
el lapso de un (1) año después de la fecha de envío (a menos que se especifique en otra parte),
siempre y cuando dichos equipos hayan sido correctamente instalados y utilizados de confor-
midad con las instrucciones del Vendedor, y siempre que dichos defectos no se deban a maltrato
o descomposición por acción química o galvánica. eSTa garanTÍa expreSa reemplaZa y
excluye cualQuier OTra garanTÍa, garanTÍa graTuiTa O prOmeSa, expreSaS O
implÍciTaS. nO exiSTen garanTÍaS implÍciTaS de cOmercialiZaciÓn O de idOneidad
para un prOpÓSiTO en parTicular. el Vendedor no asume ninguna responsabilidad por las
reparaciones hechas a los equipos del Vendedor salvo que se realicen por personal autorizado
por el Vendedor o con autorización escrita del Vendedor. el Vendedor no otorga ninguna garantía
con respecto a los materiales no fabricados por él.
Garantie n
le vendeur garantit que l'équipement fabriqué par lui et couvert en vertu de cette commande
ou de ce contrat est exempt de vices de matériau et de fabrication et, dans l'éventualité ou de
tels vices de matériau ou de fabrication se manifesteraient, il sera réparé sans frais ou, à la dis-
crétion du vendeur, remplacé franco à bord (FaB) de son point d'expédition d'origine (sauf si
spécifié ailleurs), pourvu que ledit équipement ait été installé correctement et utilisé conformé-
ment aux instructions du vendeur et, pourvu que de tels vices ne soient pas le résultat d’une
utilisation abusive ou d'une décomposition découlant d'une réaction chimique ou galvanique.
la prÉSenTe garanTie eST expreSSe, remplace eT excluT TOuTe auTre garanTie
Ou reprÉSenTaTiOn expreSSe Ou impliciTe. il n’exiSTe aucune garanTie TaciTe de
QualiTÉ marchande Ou d’adapTaTiOn À un BuT parTiculier. le vendeur n’assume
aucune responsabilité pour des réparations effectuées sur son équipement à moins qu'elles aient
été effectuées par du personnel autorisé par lui ou par une autorisation écrite de lui. le vendeur
n’offre aucune garantie pour les matériaux non fabriqués par lui.
Handle
Cartridge
Shroud
Bonnet
Nut
Temperature
Limit Stop
Cartridge Kit
FAILURE TO COMPLY WITH PROPER INSTALLATION AND
MAINTENANCE INSTRUCTIONS COULD CONTRIBUTE TO THE VALVE
FAILURE, RESULTING IN INJURY. TO ENSURE THE ACCURATE AND
RELIABLE OPERATION OF THIS PRODUCT, IT IS ESSENTIAL TO:
• properly size each valve based on the individual application.
• properly design the recirculation system to minimize pressure and
temperature variations.
• conduct an annual maintenance program to ensure proper operation
of all critical components.
• check outlet temperature to ensure it does not exceed 105°F (41°c).
make sure temperature limit stop is properly re-set to maximum 105°F
(41°c) following valve maintenance or repair. Tampering with limit
stop in any way may result in scalding temperature causing serious
bodily harm.
Periodic Inspection: Corrosive water conditions, temperatures over
210°F, unauthorized adjustments or repair could render the valve inef-
fective for the service intended. Regular checking and cleaning of the
valve’s internal components helps assure maximum life and proper
product function.
WARNING !