Powers 900 Series Biltmore Series Pressure Balancing Mixing Valves - Manual

Installation
n
Biltmore Series 900
Pressure Balancing Valves
Technical Instructions
IS-P-900
NOTE: Installation should be in accordance with accepted
plumbing practices. Flush all piping thoroughly before instal-
lation.
1. Position mixer 1
15 /
16
" ± 1 /
2
" [49mm ± 13mm] from inlet center
to finished wall surface. The tub outlet port is marked "TUB"
and should face down. Facing front of mixer, connect hot
water to left side and connect cold water to right side. The
valve has "C" and "H" cast into the body near the appropriate
inlet ports.
2. For standard inlets: Valve is factory-set for standard inlets
("TOP" stamped on stem should face shower outlet "S", see
Figure 3.) If reversed inlets are required due to back-to-back
installation (Cold water supply on the left and Hot water
supply on the right), see Figure 3 and follow instructions a–d
below:
a. Connect cold inlet to hot port ("H") and hot inlet to cold
port ("C"). NOTE: Do not turn valve upside down. If
valve is upside down, water will not flow properly
through tub spout or showerhead.
b. Turn water off with checkstops, remove high temp.
limit stop and bonnet.
c. Rotate stem 180°, and reinstall bonnet and high temp.
limit stop.
NOTE: Be certain the word "TOP" stamped on stem is facing
toward tub outlet "T".
d. Hot and Cold inlets should be re-identified for reversed
inlets to avoid confusion during future maintenance.
3. For tub and shower installations, see Figure 1. Pipe bottom
outlet port "T" directly to the diverter tub spout. The Biltmore
mixer body is designed to operate without the use of a twin
ell. Pipe top outlet port "S" to the showerhead.
Be certain that the bottom outlet port "TUB" is piped to the
tub spout; if outlet connections are reversed, the mixer will
not function properly.
4. For shower only installation, see Figure 2. Pipe top outlet
port "S" directly to the showerhead and plug bottom port.
5. Rough-in guide installation…
a. When piping installation is completed and before doing
the finished wall, slide rough-in guide onto the mixer
stem and press fit into place. (See Figure 5.)
b. The rough-in guide will insure the proper size opening
for mixer and checkstop shutoff and repair accessibil-
ity, as well as protect the chrome plated sleeve from
damage during drywall and tile installation.
6. To install dial gaskets, peel backing off gaskets and attach
gaskets to inside of dial plate.
7. After wall is completed, remove rough-in guide and attach
dial assembly and handle to mixer body with the screws
furnished. See Figure 4.
CAUTION: When soldering during installation process, do
not heat the valve any higher than the temperature required
to flow solder. Excessive overheating of the valve may cause
damage to the balancing cartridge mechanism. By following
this recommendation, you will be able to solder the valve
without removing either the cartridge or the checkstop inter-
nals. If either brazing or resistance (electric) solder is to be
used, all valve internals must be removed.
8. Maximum temperature setting must be set at the job site.
High temperature limit stop is located on the bonnet.
Remove O-ring and discard. Slide the retainer and the high
temperature limit stop out. Rotate stem to desired maximum
temperature, but no greater than 115°F (46°C). Slide back
the maximum temperature limit stop touching the tab on the
stem. Slide the retainer back all the way to secure the high
temperature limit stop. Install handle.
The maximum temperature setting must be re-adjusted if the
hot water supply temperature is changed, and also season-
ally to compensate for changes in the cold water supply
temperature.
Figure 1: Rough-in Dimensions – Tub and Shower
TUB OUTLET
TO BE PLUGGED.
PLUG BY OTHERS.
5" [127]
A
24" [609]
APPROX.
WALL
1-7/16" [37] MIN.
2-7/16" [62] MAX.
1/2" [13]
1/2" IPS CONNECTIONS
OR
1/2" COPPER SWEAT
CONNECTIONS
1/2-14" NPT
MALE INLET
ALL DOTTED LINE PIPING SUPPLIED BY OTHERS.
78" [1981]
APPROX.
TO FINISHED
FLOOR
4-5/8" [118] DIA
ROUGH-IN
GUIDE
NOTE:
'T' TO BE
ON BOTTOM
AS SHOWN
3-1/4" [82]
Figure 2: Rough-in Dimensions – Shower only
DIM P902 P905 P909 P910
A
6 1 /
4
"
(165)
7"
(178)
7"
(178)
7"
(178)
Dimensions in inches [millimeters]