RCBS Summit Reloading Press - Manual (Page 5)

INTRODUCTION
The Summit Reloading Press moves the die to the case, which allows for a unique
open design. Its 4-1/2-inch window opening provides unlimited access to the car-
tridge case, and a compound leverage linkage system requires less effort while resiz-
ing cartridges cases. A 4-1/4-inch stroke length lets reloaders seat bullets in even
the longest cartridges. The Summit’s Die Plate provides 3 inches of bearing surface
on a massive 2-inch-diameter ram, which is guided by the plate’s two rear alignment
pins. The Die Plate can use quick-change adapters and utilizes a removable 7/8”-14
threaded bushing that allows for the use of a 1”-14 bushing with larger Safari Series
dies. All Summit Reloading Press components (except the Primer Catcher) are made
of cast iron and steel to provide a lifetime of reloading pleasure. A zerk fitting has been
added to the press so the user can lubricate the Die Plate/Ram interface. The press
has an ambidextrous handle design and can be mounted flush with the edge of a
reloading bench or up to 2-1/2 inches back from the front.
ACCESSORIES
The Primer Catcher keeps spent primers from dropping to the floor and is easily
removed for emptying.
UNPACKING
Unpack the press carefully and look for the items listed below. Refer to the parts list
for identification.
• Press
• Handle/Ball Assembly
• Parts Bag: Contains Primer Catcher and 2 - 6-32 x 3/8” Button Head Cap Screws
INSTALLATION
Mount the Summit Reloading Press to a sturdy work-
bench or table with two 3/8” bolts of sufficient length
to penetrate the press base and bench. The Summit
Reloading Press may also be mounted to an optional
Accessory Base Plate II, #09280, sold separately.
Attach the threaded portion of the handle to either the
right or left side of the toggle block and lock down
using a 9/16” open end wrench in the flats provided
on the handle. See Photo 1.
The handle must remain tight at all times to avoid
damage to the handle or toggle block. An optional
Short Handle, #09291, is available for bullet seating in
the Summit Reloading Press.
Install the 2 – 6-32 x 3/8” Button Head Cap Screws
into the two holes in the front of the press base using
a 5/64” hex key wrench. Leave approximately 1/16”
between the screws and the front of the press base.
See Photo 2.
4 5
RCBS ® LIMITED LIFETIME WARRANTY
Your RCBS Summit ™ Reloading Press is warranted to be free from defects in material or workmanship
for as long as the original owner owns it. This warranty is extended only to the original consumer pur-
chaser. All RCBS products are intended for non-commercial use by hobbyists. Any other use of these
products will void the warranty. If you believe that your product is covered by this warranty, you must
return the product to RCBS at the address below, postage paid, with proof of purchase for evalua-
tion. If covered, we will (at our sole option) repair, replace or refund the purchase price of any part or
product found to be defective. This remedy will be without charge except for reasonable shipping,
handling and insurance charges. TO ENSURE ACCURACY OF YOUR WARRANTY INFORMATION,
SEND YOUR DATED PROOF OF PURCHASE TO THE ADDRESS BELOW.
This limited warranty does not cover defects or damage resulting from carelessness, misuse,
commercial use, abuse, neglect, improper installation or assembly, water submersion, unauthorized
or improper repair, failure to follow operation instructions, modification or normal wear and tear.
ANY WARRANTIES IMPLIED BY LAW SHALL IN NO EVENT EXTEND BEYOND DURATION OF THIS
EXPRESS WARRANTY. Some States do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. REPAIR OR REPLACEMENT AS PROVIDED HEREIN IS
YOUR EXCLUSIVE REMEDY FOR ANY DEFECTIVE PRODUCT. IN NO EVENT SHALL WE BE LIABLE
FOR ANY SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT
OF THE PURCHASE OR USE OF THIS PRODUCT, WHETHER BASED UPON CONTRACT, TORT,
STATUTE OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights which vary from State to State.
CONTACT US
RCBS
605 Oro Dam Blvd, Oroville, California 95965
1-800-533-5000
Email: [email protected]
Photo 1
Photo 2