Rite-Ride 2398 - Manual

2398
21-8317 05-07 NAD-34898-5
I
NSTALLATION INSTRUCTIONS
Congratulations - your new Air Helper Springs are quality
products capable of improving the handling and comfort of
your vehicle. As with all products, proper installation is the
key to obtaining all of the benefits your kit is capable of
delivering. Please take a few minutes to read through the
instructions to identify the components and learn where
and how they are used. It is a good idea to start by comparing
the parts in your kit with the parts list below.
The heart of the air helper spring kit is, of course, the air
springs. Remember that the air helper springs must flex and
expand during operation, so be sure that there is enough
clearance to do so without rubbing against any other part of the
vehicle.
Be sure to take all applicable safety precautions during the
installation of the kit. The instructions listed in this brochure
and the illustrations all show the left, or driver’s side of the
vehicle. To install the right side assembly simply follow the
same procedures.
Your kit includes separate inflation valves and air lines for
each air helper spring. This will allow you to level your vehicle
from side to side as well as from front to back. If you would
rather have a single valve inflation system, your dealer can
supply the optional "T" fitting.
I
MPORTANT
!
For your safety and to prevent possible damage to your
vehicle, do not exceed the maximum load recommended by
the vehicle manufacturer (GVWR). Although your Air Helper
Springs are rated at a maximum inflation pressure of 100
psi, this pressure may allow you to carry too great a load on
some vehicles. It is best to have your vehicle weighed once
it is completely loaded and compare that weight to the
maximum allowed. Check your vehicle owner’s manual or
data plate on driver's side door for maximum loads listed
for your vehicle.
When inflating your Air Helper Springs, add air pressure
in small quantities, checking pressure frequently during
inflation. The air spring requires much less air volume
than a tire and, therefore, inflates much quicker.
Remove the negative battery cable. It is not necessary to
jack up the truck to install this Ride-Rite kit, if you DO,
please use chocks in front of the front tires. Also, use jack
stands beneath the truck's rear axle that are properly rated to
support the trucks weight.
WARNING:
Do not inflate this assembly when it is unrestricted.
The assembly must be restricted by the suspension or
other adequate structure. Do not inflate beyond 100 psi
Improper use or over inflation may cause property damage
or severe personal injury.
224C AIR SPRING 6401 2
UPPER BRACKET 5462 2
LOWER BRACKET 5501 2
BRACKET CLAMP 5181 2
1/2" SPACER 5477 2
FUEL LINE BRACKET 5428 1
BAIL CLAMP 3077 2
AIR LINE TUBING 1
5/16" - 24 X 3/4" HEX HEAD BOLT 1
5/16" - 24 FLANGE NUT 1
5/16" FLAT WASHER 4
3/8"-16 X 8" CARRIAGE BOLT 4
3/8"-16 X 3/4" HEX HEAD BOLT 2
3/8"-16 X 2 1/2" FLAT HEAD BOLT 2
3/8"-16 FLANGE LOCK NUT 10
3/8" LARGE FLAT WASHER 2
3/4"-16 X 3" HEX BOLT 2
3/4"-16 HEX HEAD NUT 4
3/4" INTERNAL TOOTH LOCK WASHER 2
3/4" LOCK WASHER 2
3/4" LARGE FLAT WASHER 8
HEAT SHIELD 1004 1
INFLATION VALVE 3032 2
STRAIGHT FITTING 3046 2
THERMAL SLEEVE 2
NYLON TIE 6
CAUTION TAG 2
P
ARTS LIST
The air springs in this kit have a minimum
pressure of 5 psi and maximum of 100 psi after
the truck is loaded.
2WD ONLY
This kit does not require drilling into the frame.