SONIQ AWM3003 - Manual

AWM3003 AWM3003
(A)M5Ч8 Ч6 (B)M5Ч15 Ч4 (C)M5Ч30 Ч4 (D)M6Ч8 Ч4 (E)M6Ч15 Ч4 (F)M6Ч30 Ч4 (G)M8Ч15 Ч4 (H)M8Ч30 Ч4 (I)M8Ч20 Ч10
(J)M8Ч40 Ч12 (K)M8Ч65 Ч4 (M)M8 Locknut ×4 (L)Ø6 Washer ×4 (N)Ø8 Washer ×40 (O)M8 Locknut ×10 (P)M8 Spring shim ×16
(Q)Plastic sleeve ×4 (R)Square shim ×4 (S)Inner hexagon spanner S=5 ×1 (T)Inner hexagon spanner S=6 ×1 (U)S=6 Universal wheel ×4
(V)U-Steel holder ×1 (W)Top plate ×1 (X)Left lower pole ×1 (Y)Right lower pole ×1 (Z)Connective plate ×1 (AA)Left bracket ×1
(AB)Right bracket ×1 (AC)Supporting pole ×1 (AD)Flat roof plate ×1 (AE)Upper vertical ×1 (AF)Gusset plate ×2
STEP-1 STEP-2
STEP-3 STEP-4
Mount the universal wheel to the thread hole of M12 in the left lower
pole and then screw down the M12 nut. Mount the universal wheel to the thread hole of M12 in the right lower
pole and then screw down the M12 nut.
Join the left lower pole, right lower
pole and U-steel holder with M8×40
bolt pre-through a M8 washer and
a M8 Spring shim, and then screw
down with a S=6 spanner.
Join the supporting pole with
a M8×20 bolt pre-through a
M8 washer and a M8 Spring
shim, then screw down with
a S=6 spanner.
Note: When mounting, align the pins and holes in the poles.
X
U
Y
U
M12 nut M12 nut
Y
V
P
N J
X
AC
P
N
I
Before installing the mobile TV floor stand product, please make
sure your unit installing holes are well-prepared
STEP-5 STEP-8
STEP-6
STEP-9
STEP-10
STEP-11
STEP-7
O
N
AF
N
J
I
N
N
P
O
Install the two gusset plates
onto the U-steel holder and
the supporting pole with
some bolts,washer and nuts
as shown in the fig.
Mount the upper vertical pole assembled with the top plate with four
M5×8 bolts as a height needed for the TV and screw down with a
cross screwdriver.
A
Mount two M5×8 cross bolts to
the upper vertical pole and
screw down with a cross
screwdriver. Shown as the fig.
W
AE
A
Hang the two monitor brackets together
with the panel TV on the connective
plate, relax the hands until they are
caught hold of.
Install the monitor brackets onto the back of the panel TV: screw two
bolts into the holes in the back of the panel TV to install each monitor
bracket.
AA
AB
Q R
B/C/E/F/G/H
Join the connective plate and supporting pole with M6×65 inner
hex bolt pre-through a flat washer and then screw down the bolt with
S=5 spanner. Shown as the fig.
Z
K
N
N
M
Join the flat roof plate and supporting
pole with a M6×15 bolt pre-through a
M6 washer and then screw down with
a cross screwdriver.
Mobile Floor Stand Installation for Panel TV
This product is designed to mount flat panel televisions weighing up to 132lbs/60kgs with maximum flat panel mount installing
hole dimensions 80 cm(width) × 60 cm(height). It allows you to effortlessly tilt your new televusion up or down without using
tools.
Mobile Floor Stand Installation for Panel TV
E
L AD