SONIQ QPC60B - Manual (Page 3)

HANDLING AND MAINTENANCE OF A DISC.
Follow the instructions below to handle and maintain your disc in
order that long time and trouble free performance can possibly be
obtained:
= Ensure not to caress the rain bow side of the disc; handle
the disc by the edge.
= Long time exposure to sunshine, high temperatures and
humidity will damage the disc. And keep storage area clean.
= Avoid sticking labels on both sides of a disc. Writing with
pointed articles on the disc should be strictly avoided.
= Clean the disc wiping the centre and then working out to the
edge with a dry & soft cloth or a disc brush. Avoid any
cleansing lotion or chemical eradicator.
= Store them in their cases when they are not to be used.
HANDLE DISC ONLY AS SHOWN
CLEAN FROM CENTER TO EDGE
DO NOT STORE NEAR HEAT
NOTES:
NOTE: When external headphones/earphones are connected, the speakers will
be muted.
= If a particular FM (STEREO) station is weak, or you hear too much
background noise, try moving the band selector switch to the FM (MONO)
position. This can often result in a much clearer reception.
= When the band selector switch is set to FM ST. and a stereo broadcast is on
the air. The FM ST. indicator will light up.
STEREO PHONES JACK
A stereo phones jack has been provided on the side of the player so that you can
listen without disturbing others. To use this jack, plug in the headphones/
earphones (NOT INCLUDED) and adjust the VOLUME control to a preferred level.
ANTI-SHOCK PROTECTION
A special circuitry inside the player guarantees that there will be no sound
skipping when the player is subject to shock and shaking in music playback.
The laser scans the CD/MP3 disc and saves data for up to 60/120 seconds
ahead of where the playback is on the disc. In case of shocks or shaking or
vibrations, the player reads from the memory until the laser can read CD again.
But if there is too much vicious vibration or shaking exerted on the player, the
player may malfunction and sound skipping is caused.
When this happens, place the player on a level table where no vibration will be
brought. Normal sound will resume immediately.
LOAD A DISC
1. Open the CD door by the Door open area.
2. Load a disc on the disc tray with the label side facing up.
3. Close the CD door.
PLAY A DISC
1. Slide the Function switch to CD/MP3/AUX position.
2. Follow the steps above to load a disc.
3. The player begins reading disc immediately the CD door is closed,
"READING" shows in the LCD.
4. When the disc is successfully read, TOC (total of contents) shows in the
LCD and playback follows with the first track.
5. Press PLAY/PAUSE button once to halt music playback, the elapsed time of
the current track flashes to indicate the player in Pause mode; press STOP
button to cease music playback. The LCD shows the TOC again with
"STOP" on the bottom.
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY
1. Press once the SKIP UP button in music play to skip to the next track. To
skip to a specific track ahead, press this button several times.
2. Press once the SKIP DN button in music play to skip to the beginning of the
current track. To skip to a specific track at back, press this button several
times.
3. Press +10 /ALBUM button once in play to skip to the track 10 tracks ahead,
twice to skip to the track 20 tracks ahead. You can reach the last track of the
disc using this button. Press this button again at the last track of disc to go to
the first track for playback.
4. Hold the SKIP UP button in music play to search at quick rate for a specific
point to play.
5. Hold the SKIP DN button in music play to search at quick rate for a specific
point to play.
REPEAT A SINGLE TRACK
To repeat a preferred track in playback, press MODE button once, "REPT 1"
shows in the LCD. Then select the preferred track using SKIP UP/DN buttons or
+10/ALBUM button. The player will repeat the chosen track until you press
STOP button.
REPEAT ALL TRACKS
To repeat all tracks, press MODE button twice in play mode, "REPT ALL" shows
in the LCD. The player will repeat all tracks until you press STOP button.
INTRODUCTION PLAY
Introduction play is that the first ten seconds of each track are played in a
sequential order. Press MODE button three times to enter this mode during play,
"INTRO" shows in the LCD. Press PLAY/PAUSE button to begin Introduction
play from Track NO.1. Press PLAY/PAUSE button to exit Introduction play mode
and normal music play resumes. Press SKIP UP button in Introduction mode to
begin Introduction play from the next track immediately after the current track.
Press SKIP DN button in Introduction mode to begin Introduction play from the
current track.