SoundOff Signal Intersector Surface Mount - Manual

INTERSECTOR™ LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website.
If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to skip the automated message.
Questions or comments that do not require immediate attention may be emailed to [email protected].
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
Intersector™ LED Light ENT3(x)3(x).pdf ~ Rev. 03.12 Pg. 1
OPERATION:
For details on operation see page with ‘Flash
Patterns’ table on last page.
Please see last page for
Technical Specifications
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
Important Information:
WIRE HOOK-UP TABLE
WIRE COLOR:
(ALL WIRES 20ga)
CONNECT TO:
(FROM FLASHER ONLY)
RED +10-16 Vdc
WHITE Pattern Select / Sync
BLACK
Ground (-)
GREEN
Cruise Mode
(+10-16 Vdc)
! WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
IMPORTANT:
Power should only be
supplied through RED
WIRE of flasher harness
and must be fused with
a 3A, user supplied,
in-line fuse. Failure to
install this fuse will create
a fire hazard and will
damage the Intersector™
Light. Connecting the
Intersector™ light to any
power source directly
WILL permanently
damage the light and will
void warranty.
IMPORTANT! FOR
PROPER OPERATION
ALL WIRES MUST BE
CONNECTED FROM
FLASHER TO LIGHT
HEAD.
GREEN BLACK RED WHIT
E
1 3 2 4
1 3 2 4
GREEN BLACK
RED
WHIT
E
FEMALE
CONNECTOR
MALE
CONNECTOR
FROM FLASHER
INTERSECTOR
LIGHT
ALL WIRES 22ga
SURFACE MOUNT
INSTALLATION:
1. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
2. Use the gasket provided as a template to
mark locations of wire and mounting
screws
3. Use a 5/8” diameter drill for the wire holes
4. Size pilot holes for mounting screws
appropiately.
5. Fasten light using bezel and mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
DECK/ GRILLE BRACKET
INSTALLATION:
(PURCHASED SEPARATELY)
1. Slide wire from Bezel through center
access hole in the gasket and bracket.
2. Next, position the Housing over the Bezel
and align the holes with the bracket.
3. Lastly, using the supplied 8-32 x 1”
screws fasten the assembly lightly. Do
not torque mounting screws beyond 20
in - lbs.
4. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
5. Use the bracket provided as a template to
mark locations of mounting screws.
6. Size pilot holes for mounting screws
appropiately.
7. Fasten light using bezel and mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
SURFACE MOUNT
DECK/ GRILLE BRACKET MOUNT
BRACKET
GASKET
BEZEL
HOUSING
8/32 x 1” PHIL PAN SCREWS