SoundOff Signal GHOST Spot Multi Mount - Manual

1.800.338.7337 / www.soundoffsignal.com
IMPORTANT INFORMATION:
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800.338.7337 (press #4 to skip the automated message).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
EGHSTS1(xx) 07.14
Important Information:
OPERATION:
WIRE CONNECTIONS
1. Connect the GHOST BLACK wire to a
good, convenient ground.
2. Connect the GHOST RED and WHITE
wire to one side of a user supplied on/
off switch. Connect the other side of the
switch, through a 3Amp fuse, to a source
of +10-30Vdc. Both RED and WHITE
wires MUST be connected to power.
NOTE: The GHOST is a factory sealed unit
that CANNOT be serviced in the field. Any
attempt to gain access to the GHOST unit
will most likely cause permanent damage
and void its warranty.
WIRE HOOK-UP TABLE
WIRE COLOR: CONNECT TO:
RED +10-30Vdc
BLACK Ground (-)
WHITE +10-30Vdc
This product contains high
intensity LED devices. To prevent
eye damage, DO NOT stare into
light beam at close range.
WARNING !
TECHNICAL
SPECIFICATIONS
Overall
Dimensions:
4.0”L x 0.88”H x
1.75”D
Input Voltage
Range:
10-30Vdc
Current
Consumption:
0.45A @ 12.8Vdc
0.23 @ 25.6Vdc
# of LEDs: 6 Generation 3 LEDs
Operating
Temperature:
-40º to +65º C
INSTALLATION:
1. Screw Mount - Establish a position
on the vehicle. Use the mounting slots as
a template to mark hole locations. Drill a
hole using a #27 drill bit. The Torx screws
provided are self-tapping.
2. Adhesive Mount - To obtain optimum
adhesion, the bonding surfaces must be
well unified, clean and dry. Peel one side
of each adhesive mounting patch provided.
Apply each rectangular patch to the bottom
of the GHOST housing. Position the GHOST
on the vehicle and mark 2 edges of the
location using tape. Peel the remaining
paper from the adhesive patch and carefully
position the light using the tape template.
Press down on housing firmly to insure
good adhesive contact. Important: Apply
carefully; adjustment is not possible after
the adhesive bonds. Ultimate strength of
adhesive is achieved after 24 hours.
3. ‘U’ bracket - Open the hood or trunk that
will be the attachment surface. Place the
rubber pad provided on the surface, insuring
that the lower lip is on the edge of the sheet
metal. Fit the ‘U’ bracket to the back of the
GHOST light base, nesting the bracket holes
with the pins on the light base. Slide the
assembly onto the rubber pad. Tighten the
four set screws.
Loosen the two #10 TORX screws on
the back of each housing to adjust the angle
of the GHOST. After adjustment, tighten the
TORX screws. Adhesive Mount
‘U’ bracket
Supplied #10-24
3/8” lg. hex drive
set screw
Screw Mount
Hole with #27 drill
Supplied #10 thread
forming screw.
GHOST® SPOT LIGHT, MULTI-MOUNT
EGHSTS1(x) - Black
EGHSTS1(x)W - White