SoundOff Signal INTELLIswitch993 Switch w/ Power Pursuit User Manual
Page 2
All of the Standard switches S1 through S6 can be associated with any of the
Pursuit switches. Thus, when in normal operation, any combination of
switches S1 - S6 can be activated just by pressing a Pursuit switch. Each
Pursuit switch can be programmed with a different combination of S1 - S6.
Special Note: Programming a Standard switch as momentary cancels any
Pursuit switch association that may exist with that switch.
To Enter Program Mode:
1. Press and hold switches S1 and S2 for 5-seconds.
All back lights will blink OFF then ON twice;
Pursuit switch P1 will start to flicker;
indicating panel is in Pursuit Program Mode.
2. Press each switch S1 - S6 you want associated with Pursuit Switch P1.
Selected switch will flicker;
indicating it has been associated with the Pursuit switch.
*Any number and combination of Standard switches
may be associated with each Pursuit switch.
3. Press Pursuit switch P2 and repeat step 2 (Pursuit switch P2 will flicker).
4. Press Pursuit switch P3 and repeat step 2 (Pursuit switch P3 will flicker).
5. To exit Pursuit program mode, press the Pursuit switch that is flickering a
second (2nd) time.
Note: All of the switch buttons will illuminate with a chase pattern
to indicate the start of normal operation.
If no button is pressed for 60-seconds, the panel will exit program
mode automatically.
1. Press any switch one (1) time to turn it On and press again to turn it OFF.
2. Press any Pursuit switch (See Program Pursuit Switches Section);
Switch back light turns ON and all associated standard switches (S1 - S6) turn ON.
3. Press *Gunlock switch. (*See note above to use Gunlock switch as light bar flash pattern selector.)
A momentary +12v signal is present at the gunlock output as long as button is pressed.
4. Dimmer Switch (Bright, Medium, Low & Off).
The brightness level can be changed (whenever no Pursuit Switches are active) by pressing dimmer switch to sequence through the levels.
Brightness level will remain until panel is powered OFF and will return to default when powered back ON.
To save the chosen brightness level as the default, select desired brightness level then press and hold dimmer switch for 5-seconds.
Display will flash ON and Off three times to indicate that the setting has been saved as the default.
Note: If the brightness level is set to OFF, the brightness will automatically be adjusted to LOW when any switches are ON.
Circuit Protection
Each standard switch output is protected by an electronic smart switch (2 Amp).
Any time an over voltage or over temperature condition occurs, the output shuts OFF until condition is corrected.
Once problem is corrected, function will automatically turn back ON.
Notes:
There is no status indicator for an over voltage or over temperature condition.
The power wire must be fused near battery at 15 Amps.
The logic circuit is internally protected by a 2 Amp fuse.
Program Pursuit Switches
All switches can be set as momentary.
Additionally, Switch 6 can be set as a timed output of 1 to 25
seconds.
Special Note: Programming a Standard switch as momentary
cancels any Pursuit switch association that may exist with that
Standard switch.
To Enter Momentary Program Mode:
1. Press and hold switches S5 and S6 for 5-seconds.
All back lights will blink ON and OFF twice;
Pursuit switch P3 will start to flicker;
indicating panel is in Momentary Program Mode.
2. Press each switch that you want to program as momentary once.
Switches programmed as momentary will flicker.
3. To exit Momentary Program mode,
press Pursuit switch P3 a second (2nd) time.
Note: All of the switch buttons will illuminate with a
chase pattern to indicate the start of normal operation.
If no button is pressed for 60-seconds, the panel will
exit program mode automatically.
To Program Switch 6 as Timed Momentary
1. Repeat Step 1 above.
2. Press and hold Switch 6 for as long as you want the timer to run
during operation. (Switch will flash for the timed number of seconds
programmed)
3. Repeat Step 3 above.
Program Momentary Switch Options
S1
S2
S3
S4
S5
S6
Dimmer
*Gun
Lock
P1
P2
P3
Pursuit Switch Flickers to
indicate Pursuit Program Mode
Press and Hold
5-seconds
Press and Hold
5-seconds
Program Pursuit Switch
Program Momentary Switch
Panel Front View
ETSP993 Operation
Standard Switches
S1 - S6
Pursuit Switches
P1 - P3
Hidden
Switches
Walk-About-Test - Press and Hold 5-seconds
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com
and select the “Warranty & Returns” link along the left column of our home page. If you have questions regarding this product please contact Technical
Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to skip the automated message. Questions or comments that do not require
immediate attention may be emailed to [email protected].
1.800.338.7337 / www.soundoffsignal.com / Thank you for trusting us with your safety!
*The Gun Lock output wire may
be hooked up to a flash pattern
selector output (ie. on a light bar).
The flash patterns can then be
selected by pushing the hidden
switch button to cycle through the
options.
ETSP993_C.CDR 2011-05-08
Page -2-
NST12020-2_C