SWIT Electronics S-2050 - Manual (Page 2)

Usage
1. Power supplies
S-2040
S-2040 is 6-17V voltage input and offers various power supply methods.
● By S-8040 battery
① Make sure there’s no power lead connected into DC-IN socket and the light is
switched off (turn the switch to “
〇”).
② Press and slip off the protection cover. See Fig 3
③ Align a fully charged S-8040 battery to the DV mount slot to same side, and
press tightly in. Slide the battery downward to snap together. See Fig 4
● By DV battery
① Press and slip off the protection cover. See Fig 3
② Align the mount S-7004 to the DV mount slot to same side, and press tightly
in. Then slide the S-7004 mount downward to snap together. See Fig 5-
①
③ Fix the DV mount with two screws.
④ Make sure the light is switched off (turn the switch to “〇”). Mount a fully
charged battery to the S-7004 mount. Fig 5-
②
Remark: After use, please fix on the protection cover.
There’re the following types of S-7004 for choice: (Optional Purchase)
Model Compatible battery type Recommended SWIT battery
S-7004F SONY NP-F770/970 S-8972, S-8970, S-8770
S-7004P Panasonic CGA-D54S/D28S S-8D62, S-8D54, S-8D28
S-7004J JVC BN-V428U S-8428
S-7004C Canon BP-930/945 S-8945, S-8845
S-7004U SONY BP-U60/30 S-8U62
S-7004E Canon DSLR LP-E6 S-8PE6
S-7004B Panasonic VW-VBG6 S-8BG6
S-7004V JVC BN-VF823 S-8823
● By DC adaptor S-7104
① Make sure the light is switched off (turn the switch to “〇”). Plug the pole end
of S-7104 into the DC-IN socket.
② Plug the D-tap end of S-7104 to the camera auxiliary power tap or the
battery’s D-tap output socket. See Fig 6.
S-2050
S-2050 is 11-17V voltage input and only accepts D-tap power supply.
By DC adaptor S-7104
① Make sure the light is switched off (turn the switch to “〇”). Plug the pole end
of S-7104 into the DC-IN socket.
② Plug the D-tap end of S-7104 to the camera auxiliary power tap or the
battery’s D-tap output socket. See Fig 6.
2. Fix the LED light to the camera
● By cold shoe
Anticlockwise screw the knob to draw the bolt back, slide the cold shoe mount into
camera, and then clockwise adjust the knob to fasten. See Fig 7.
● By screw mount
Fix the cold shoe slot to the screw mount by the screw. Fix the light to the cold
show as the above Instructions. See Fig 8.
3. Adjust the angle of the light:
Hold the light, and adjust the light upward or downward. See Fig 9.
4. Open barn doors and filters:
Open the barn doors and filters to about 45°.
5. Switch on:
Turn the switch to “ I ”.
6. Adjust the illuminance:
Adjust the illuminance from 10% to 100% by the dimmer.
7. Adjust color temperature:
Output 5600K light by using 5600K filter; Output 3200K light by using 3200K filter
Fig 4
Release button
Screw hole
Battery
release
Fig 6
Pole plug
Fig 7
Fig 9
Adjust upward
or downward
Fig 5
Fig 8
Press and slip
to release
Fig 3
ONLY S-2040
ONLY S-2040
ONLY S-2040