Teradek Bond II - Manual

Stream Joystick:
, : Selects options from streaming/recording prompts
● (button press) : Returns to main status screen, start/stop recordings and broadcasts
Menu Joystick:
▲ , ▼ : Select menu items, change status screen on main display, select characters
: Back, move to higher menu level
, ● (button press) : Confirm selection, open selected menu
▲ ▲
▲
▲
DEVICE CONFIGURATION
BROADCAST CONFIGURATION
L: Video Input
M: Encoder Status
N: Broadcast/Record
O: Fault/Error
P: Stream Joystick
Q: Menu Joystick
Use the included ¼"-20
and hot shoe mount to
attach Bond
II to your camera.
Connect one or more modems to Bond II’s USB ports.
If desired, attach top plate, modem clips and velcro
to secure the modems.
• Via WiFi – Attach antennas to (J) . Open your computer’s wireless network configuration and find
Bond II’s WiFi network (Teranet – XXXX, where XXXX is the last four digits of Bond II’s serial number)
• Via Ethernet – Connect Bond II to a wired network or directly to your computer.
1. Open a web browser and enter the IP address of Bond
II. View the WiFi IP address by pressing
▼ once
and the Ethernet IP address by pressing ▼ twice.
2. Log into Bond II – The username is admin and the default password is admin.
1. Navigate to Video Setup > Bonding.
2. Enter a Sputnik Host Address. For Sputnik server setup instructions please see the Sputnik Setup Guide
(http://www.teradek.com/pages/downloads).
3. Confirm the Sputnik Port matches your Sputnik server’s configured inbound port. The default value is 5111.
4. Adjust the Max Bitrate and Max Buffer Length settings, if desired.
5. Click Apply.
6. Confirm that data is reaching Sputnik by navigating to the server’s Dashboard, or by verifying
activity on the modem activity LEDs
(K) .
1. Select Live Internet Streaming as the Stream Mode.
2. Select your provider.
3. Enter your user name and password, click login.
4. Select your Channel and click Apply.
5. Start/stop the stream with the buttons on the Stream Settings page or with the Stream Joystick.
1. Select RTMP as the Stream Mode.
2. Enter the server URL. Depending on your destination (local server or CDN), this will look similar to
rtmp://server.address:1935/live.
3. Enter the stream name. For many platforms this is found with the server URL.
4. Click Apply.
5. Start/stop the stream with the buttons on the Stream Settings page or with the Stream Joystick.
SETUP
1
2
3
1
3 2
AC adapter SDI HDMI
NEED MORE HELP?
1. Support forum: http://support.teradek.com → Contains tips, information and all the latest firmware & software updates.
2. Training videos: http://www.teradek.com/trainin
g
TERADEK SUPPORT STAFF: support @teradek.com or call 888−941−2111 ext2 (Mon−Fri 7am to 6pm PST)
*Modems not included
L
N
O
P
Q
WEB UI LOGIN
username: admin
password: admin
M
A
B
I
J
K
A: Modem Clips
B: Top Plate
C: Video Input (SDI or HDMI)
D: Mic/Line Audio Input
E: Headphone Output
F: Power Input
G: Power Switch
H: OLED Display
I: Status LEDs
J: Antennas
K: Modem Activity LEDs
G
F
E
D
C
H
Connect a power source to Bond II’s DC input (F) and a
video input to (C) .
Configure the following from the Video Setup > Stream Settings page.
Sputnik
Decoder
Primary Stream
Mode: MPEG Transport Stream
Transport Stream Server: Enabled
Listening Port: 5000
Decoder Settings
Mode: MPEG Transport Stream
Protocol: TCP Pull
Host: Your Sputnik Server Address Port: 5000
1. Configure the following settings on Bond II. 2. Configure the following settings on your decoder.
MPEG TRANSPORT STREAM
CONNECT TO BOND II
CONFIGURE BONDING SETTINGS
LIVESTREAM/USTREAM
RTMP STREAMING