Triton ETA 100 - Manual (Page 7)

7
GB
WARNING. Read all instructions. Read all
safety warnings and all instructions. Failure
to follow the warnings and instructions my result
in electric shock, fire and/or serious injury.
Save these instructions
1. WORK AREA SAFETY
a. Keep work area clean and well lit. Cluttered and
dark areas invite accidents. b. Do not operate
power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may
ignite the dust or fumes. c. Keep children and
bystanders away while operating a power tool.
Distractions can cause loss of control.
2. ELECTRICAL SAFETY
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep the cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use, this will
reduce the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply, which will reduce the risk of
electric shock.
3. PERSONAL SAFETY
a. Do not use power tools while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b. Always use safety equipment: wearing eye
protection, dust mask, non-slip safety shoes,
hard hat and hearing protection used in
appropriate conditions will reduce personal
injuries.
c. Avoid accidental starting. Ensure the switch is
in the ‘Off’ position before plugging in. Carrying
power tools with your finger on the switch or
connecting to power with the switch on the ‘On’
position invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e. Do not over-reach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f. Wear suitable clothing and footwear. Do not
wear loose clothing, neckties, jewellery, or other
items which may become caught. Wear non-slip
footwear or where appropriate, footwear with
protective toe caps. Long hair should be covered
or tied back.
g. If devices are provided for the collection of
dust particles, ensure these are connected and
properly used. Use of these devices can reduce
dust related hazards.
4. POWER TOOL USE AND CARE
a. Do not force the power tool. Using the correct
power tool for your application will be safer and
produce better results at the rate for which it
was designed.
b. Do not use the power tool if the ‘On/Off’ switch
is not working correctly. Power tools that cannot
be controlled by the switch are dangerous and
must be repaired prior to use.
c. Disconnect the plug from the power source
before making any adjustments, changing
accessories or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Power tools are dangerous in the hands of
untrained users. Store power tools out of reach
of children, and do not allow persons who are
unfamiliar with the product or these instructions
to operate the power tool.
e. Maintain power tools. Check for misalignment,
binding or breakage of moving parts, and any
other condition that may affect the operation of
the power tool. If damaged, have the power tool
SAFETY INSTRUCTIONS
Safety Instructions