Canon DR-5010C - Manual (Page 2)

☞
Continued from front side
1. Launch CapturePerfect 3.0 from the Programs menu in Windows.
2. Select [Select Scanner] from the Scan menu.
The Scanner Selection dialog box appears.
3. Select [Canon DR-5010C] and click [OK].
12. When all installations are complete, the
installation completed screen appears.
Click [Exit] to exit the installer. Click [Back] to
return to the menu screen.
1. When connecting the scanner with a SCSI cable, turn your computer OFF.
2. Make sure the scanner’s power switch is in the OFF position.
If the power switch is in the ON position, press the switch to turn it to the OFF
position.
OFF Position
Power Switch
ON Position
3. Plug the power cord into the power connector on the rear of the scanner ( 1 1 1 1 1 ).
4. Plug the power cord into the power outlet ( 2 2 2 2 2 ).
5. When connecting the scanner with a USB cable, use the supplied USB cable.
Type B
Type A
6. Follow the steps below when connecting the scanner to your computer with a
SCSI cable.
6-1 Turn OFF your computer.
Make sure your computer is turned OFF before connecting the SCSI cable.
Connecting the Scanner to Your PC
The scanner can be connected to a computer in two ways: by USB connection to a
standard USB port on the computer, or by SCSI connection to a SCSI card installed in
one of the computer’s expansion slots. Select a connection method appropriate to
your computing environment.
SCSI Connector
(Half-pitch 50-pin, pin-type) USB Connector
Imprinter Connector
SCSI ID
Dip Switches
Power Connector
This completes the software installation.
Next, you need to connect the scanner to your computer. ( ☞ STEP4)
Turning On the Power (Scanner
Recognition)
When you turn the scanner connected to the PC ON, the plug-and-play function recognizes
the scanner, and the device driver is automatically installed.
Note
● Windows 2000/XP/Vista possess an event feature that allows you to launch a
scanning application with the start key on the scanner. CapturePerfect 3.0
supports this feature and, once setup is complete, can be launched by pressing
the scanner’s start key.
● When multiple applications that support the event feature are installed, pressing
the start key displays an Event on device dialog box for selecting the desired
application.
● You can change the event settings to specify a priority application from among
multiple applications or to turn off the event feature. For details, refer to “Setting
the Event Function” on page 40 of the User’s Guide.
The setup is now complete
This completes the setup of the DR-5010C. Details on how to use the DR-5010C are
described in the User’s Guide packaged with the scanner. Before you start using the
scanner, make sure to thoroughly read the User’s Guide.
Warning
6-2 Connect the scanner to your computer with the SCSI cable.
SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the
shape of the connectors on your SCSI card and the scanner.
Warning
The scanner is now connected to your computer.
Next, you need to turn on the scanner and ensure Windows recognizes
it. (
☞ STEP5)
Warning
1. Check the connection between the scanner and the computer.
2. Press the power switch to turn the scanner ON (when connecting by SCSI).
The power indicator and start key indicator both light green.
3. Turn ON your computer.
ON Position
Power Switch
Power indicator
Start key
4. Windows recognizes the DR-5010C as new hardware and performs installation
automatically.
(Windows 2000)
(Windows XP) (Windows Vista)
Note
● For Windows XP/Vista, a balloon help pop-up appears when installation is finished.
(Windows XP) (Windows Vista)
● The installation finished message does not appear in Windows 2000.
● The scanner is registered on the computer as “CANON DR-5010C USB” (or
“CANON DR-5010C SCSI”) in the “Imaging Device” directory of the Device
Manager.
Selecting the Scanner
You must select your scanner before using it with an ISIS- or TWAIN-compatible scanning
application.
The menus and procedures for selecting the scanner are different for each application.
For details, refer to the manual for your scanning application when selecting the scanner.
This section explains the procedure for selecting the scanner with “CapturePerfect 3.0”.
For details on how to use CapturePerfect 3.0, refer to the “CapturePerfect 3.0 Operation
Guide” in the Programs menu of Windows.
The scanner is now correctly recognized by your computer.
Next, you need to select the scanner with the scanning software.
(
☞ STEP6)
❏ Do not use both a USB connection and a SCSI connection at the same time.
❏ Use only the supplied power cord.
❏ Connect the scanner to your computer while the scanner is turned OFF.
❏ Before connecting the scanner with a SCSI cable, turn your computer OFF.
❏ A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches
the shape of the connectors on your SCSI card and the scanner.
❏ When using the scanner in a daisy chain connection with other SCSI devices,
pay attention to the following points:
● The default setting for the SCSI ID is “SCSI ID=2.” Set the dip switches so
that the scanner’s SCSI ID is different from all other SCSI devices on the
chain.
1
ON
2
Default Position (SCSI ID=2)
SCSI ID
2
3
4
5
SW1
OFF
ON
OFF
ON
SW2
OFF
OFF
ON
ON
OFF
Dip Switches
● The scanner has a built-in SCSI terminator that is permanently set to [ON].
When using the scanner in a daisy chain connection, make sure that it is
connected as the terminating device and that the terminators of all other
SCSI devices in the chain have been set to [OFF].
❏ When the scanner is connected by a SCSI cable, always turn on the scanner
before the computer. Turning on the computer first may prevent it from recog-
nizing the scanner properly.
❏ Log on to Windows with an account that has administrator privileges.
❏ Wait at least 10 seconds before turning the scanner on again after turning it
off.
❏ If the scanner will not be used for an extended period, be sure to unplug it
from the power outlet for safety.