Waring DMC180DCA - Manual (Page 2)

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE
WASHING: DIVERSEY WYANDOTTE 4 TABLESPOONS/GALLON HOT (115˚ F)
DIVERSOL BX/A OR CX/A
RINSING: PLAIN WATER WARM (95˚F)
SANITIZING: CLOROX ® INSTITUTIONAL 1 TABLESPOON/GALLON COLD (50˚ F -
BLEACH 70˚ F)
+
A. B. C.
Circuit Grounding Conductor
Connected Properly
Grounding Prong
Adapter
Grounding Lug
Cover
Mounting
Screw
Cover of Grounded Outlet Box
CLEANING & SANITIZING INSTRUCTIONS
1. Rinse container thoroughly under running water. Add 8 ounces of clean
rinse water to container. Place container in normal operating position on
mixer and run on high speed for two (2) minutes. Empty container.
2. UNPLUG POWER CORD FROM ELECTRICAL OUTLET.
3. Loosen and remove thumbscrew. Unscrew and remove on/off switch
actuator knob.
4. Carefully remove stainless steel panel.
5. Wash, rinse, and sanitize thumbscrew, on/off switch actuator knob, stain-
less steel panel, and container. Sanitize these parts by immersing in
sanitizing solution for two (2) minutes. Shake off excess moisture and
allow parts to air dry.
6. Working from the top down, wash, rinse, and sanitize the portion of the
mixer housing situated directly over the container, and the portion of the
spindle above the agitator, using absorbent wiping cloths moistened with
cleaning solution, rinse water and sanitizing solution.
7. Reassemble panel, on/off switch actuator knob, and thumbscrew to mixer
housing.
8. Wash, rinse, and sanitize the agitator and the bottom of the spindle as
follows:
❑ Plug power cord into electrical outlet.
❑ Add 8 ounces of washing solution to container and place in normal
operating position on mixer.
❑ Run on high speed for a minimum of two (2) minutes.
❑ Empty container, and repeat two-minute run with 8 ounces of rinse
water.
❑ Empty container, and repeat two-minute run with 8 ounces of
sanitizing solution.
❑ Empty container. Run motor for a few seconds with empty container in
normal operating position to spin off any excess moisture. Empty
container. Do not rinse container, spindle, or agitator after sanitizing is
completed.
❑ Allow all parts to air dry.
Wash, rinse, and sanitize as outlined above prior to initial use, and whenever
mix will not be used again within a period of one hour.
Surfaces of the mixer housing which are outside of the food-contact areas
may be cleaned as required, using wiping cloths moistened with cleaning
solution, rinse water, and sanitizing solution. UNPLUG POWER CORD
FROM ELECTRICAL OUTLET BEFORE CLEANING HOUSING.
Prevent liquid from running into housing by wringing all excess moisture
from wiping cloths before using them.
Washing solutions based on non-sudsing detergents and chlorine-based
sanitizing solutions having a minimum chlorine concentration of 100 PPM
are recommended.
The following washing, rinsing, and sanitizing solutions, or their equivalents,
may be used.
Green/Yellow: Earth Ground • Blue: Neutral • Brown: Live
GROUNDING INSTRUCTIONS
• For your protection, Waring Commercial Mixers are equipped with a 3-
conductor cordset.
• 120 Volt units are supplied with a molded 3-prong grounding-type plug
and should be used in combination with a properly connected grounding
type outlet as shown in Figure A.
If a grounding type outlet is not available, an adapter, shown in Figure B,
may be utilized to enable a 2-slot wall outlet to be used with a 3-prong plug.
Referring to Figure C, the adapter must be grounded by attaching its
grounding lug under the screw of the outlet cover plate.
Caution: Before using an adapter, it must be determined that the outlet
cover plate screw is properly grounded. If in doubt, consult a licensed
electrician.
Never use an adapter unless you are sure it is properly grounded.
Note: Use of an adapter is not permitted in Canada.
• 240 Volt units are supplied without a plug, and an appropriate one must be
installed by user in accordance with local electrical codes observing the
following cordset conductor color coding:
OPERATION
After adding materials to be mixed, place container on mixer so that its top
rim engages the spring-loaded on/off switch actuator knob. Slide actuator
knob upward with rim of container to start motor. Seat bottom of container
onto container support.
When mixing is finished, disengage container from support and carefully
lower it, allowing spring-loaded switch knob to slide back down and stop
motor.
On two-speed models, HIGH or LOW speed operation is selected by a
rocker switch located on the top of the mixer housing.
Counter-top models are equipped with Xa U-shaped stabilizing leg on the
base of the unit. For maximum stability, the leg should be unfolded and fully
seated in position, projecting from the rear of the base.