Monarch Instrument Remote Contact Assembly - Manual

Remote Contact Assembly (RCA)
SAFEGUARDS AND PRECAUTIONS:
WARNING: Making measurements in direct contact
with rotating equipment can be dangerous. Keep all
loose clothing and hair away from exposed moving
machinery. Keep the hand holding the RCA well behind the
front fl ange of the Remote Contact Assembly. Properly replace
all the machinery guards after completing measurement. Do
not use for rotation greater than 20,000 RPM.
Not designed for continuous operation.
The RCA is an accessory for measuring contact RPM, linear speeds
or totalizing lengths. It needs to be plugged into a tachometer to be
functional. It is supplied with two rubber tips (one concave and one
convex) and a 10 cm wheel. An optional 12 inch wheel is available.
When used with the Monarch Pocket Laser Tach 200, the unit outputs
12 pulses per revolution (ppr). The maximum operating range of the
RCA is 20,000 RPM when used with a contact tip and 12,000 RPM when
used with a linear wheel.
The RCA plugs into the 3.5 mm stereo input jack of the tachometer.
Connector pinouts are as shown below.
To measure rotational speed (RPM), select either a convex or concave rubber tip
appropriate for the measurement to be made and install it fi rmly on the shaft of the RCA.
Note that the shaft has a fl at surface that must align with the fl at in the rubber tips. The
pointed convex (conical) tip is used for moderate to large diameter shafts that are equipped
with a turned center, while the concave (inverted conical) tip is used on smaller diameter
shafts. The circumference of the concave tip is 1.0 inch (2.54 cm).
Refer to the tachometer’s operating instruction on how to set up the tachometer for contact
measurement of speed, rate, or totalization.
To make a measurement, start the rotating equipment and carefully move the contact tip
against the center on the end of the rotating shaft. Keep the hand holding the RCA well
behind the back edge of the front fl ange of the RCA. Use only a moderate amount of
pressure to keep the rubber tip in contact with the rotating shaft.
Surface speed linear rate measurements are made with the Linear Speed Wheels. The 10 cm Linear
Speed Wheel must be pushed back onto the shaft, aligning the fl ats. Secure it in position by fi rmly
tightening the small machine screw on the wheel. The optional 12 inch wheel also has a slot that must
engage with the pin in the RCA shaft and a locking screw which must be tightened.
WARNING: Do not attempt to use the Linear Speed Wheel if the securing screw is not
tight.
To measure a linear surface speed and/or total length such as a moving belt, roll or web, fi rst select
the Rate (Linear Contact) or Total mode on the tachometer and set the wheel size (10 cm or 12 inch).
Hold the RCA at a right angle (90 degrees) to the direction of movement and gently contact the rubber
edge of the wheel against the belt or top surface of the object to be measured. For accurate results, be sure that the wheel edge is held
perpendicular (at 90°) to both the measurement plane and the direction of travel. Only a very moderate amount of pressure is required.
Excess pressure can load the RCA shaft causing an erroneous reading and eventual wear in the bearings of the RCA.
In order to comply with EU Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE):
This product may contain material which could be hazardous to human health and the environment. DO NOT DISPOSE of this product as unsorted municipal waste. This product needs to be
RECYCLED in accordance with local regulations, contact your local authorities for more information. This product may be returnable to your distributor for recycling - contact the distributor for details.
Monarch Instrument
15 Columbia Drive Amherst, NH 03031-2334 www.monarchinstrument.com
Tel: 603-883-3390 Fax: 603-886-3300 E-mail: [email protected]
1071-4839-114R
022613
Reads both directions
of movement
Linear
Contact
Wheel
Securing
Screw
⊳
⊳
Remote Contact Assembly with 8 ft (2.5 m) cable,
contact tips and two linear speed wheels
(12 inch wheel sold separately)
RCA Output Connector - Connection Detail
SENSOR POWER
SUPPLY IN
SIGNAL OUTPUT
COMMON (GND)