Amico Mira 45 - Manual (Page 5)

www.amico.com 5
Operating manual (GB)
Page 14/40
4. Assembly and Installation MIRA 45 Single Ceiling
Note: Only qualified technicians should carry out MIRA 45 installation.
Two people are required for assembling the MIRA 45 Single Ceiling. The supply
voltage must correlate with the voltage noted on the fixture’s rating label. The
ceiling fitting is to be used exclusively at ceilings that are either solid, or
supplied with a suitable high-strength ceiling-mounting solution.
Mounting steps
c Drill holes in accordance to the enclosed drilling template (∅=8mm;
depth=55mm). Clean out the drilled holes. Attach the anchor plate using
the four anchor bolts. Tap the anchor bolts completely in, using a hammer.
Tighten the nut with an open-ended wrench (approx. 3-4turns, 23Nm
torque).
Detailed view 1
d Perform this Step on a flat and level surface. Pull the cable through the
support tube. Insert the slider into the groove of the arm joint, noting the
location of the fixing hole (see detailed view 1 part ‘a’). Slide the arm and
support tube together (view 1, direction ‘b’). Align the hole in the slider with
the set-screw hole at the bottom of the support tube. Insert the set-screw
into the hole to lock the slider in place (1c). Tighten the set-screw
completely, then loosen it by a maximum 1-quarter turn and check the
operation of the arm joint.
Check: Set-screw has to be flush.
Detailed view 2
e Place the O-ring and the ceiling cover over the support tube. Insert the
support tube into the anchor plate and fix it temporarily, using supplied
bolts (see detailed view 2). Align the support tube to the direction of the
fixture’s general usage. Tighten the screws on the anchor plate. Now
connect to the electrical power supply, as per the wiring diagram (see
sheet enclosed with the set of bolts). Slide the ceiling cover and the O-ring
upwards.
f Head Assembly (see page
6
8)
Before mounting the MIRA 45 Single Ceiling, take heed of the operating range.
Operating manual (GB)
Page 14/40
4. Assembly and Installation MIRA 45 Single Ceiling
Note: Only qualified technicians should carry out MIRA 45 installation.
Two people are required for assembling the MIRA 45 Single Ceiling. The supply
voltage must correlate with the voltage noted on the fixture’s rating label. The
ceiling fitting is to be used exclusively at ceilings that are either solid, or
supplied with a suitable high-strength ceiling-mounting solution.
Mounting steps
c Drill holes in accordance to the enclosed drilling template (∅=8mm;
depth=55mm). Clean out the drilled holes. Attach the anchor plate using
the four anchor bolts. Tap the anchor bolts completely in, using a hammer.
Tighten the nut with an open-ended wrench (approx. 3-4turns, 23Nm
torque).
Detailed view 1
d Perform this Step on a flat and level surface. Pull the cable through the
support tube. Insert the slider into the groove of the arm joint, noting the
location of the fixing hole (see detailed view 1 part ‘a’). Slide the arm and
support tube together (view 1, direction ‘b’). Align the hole in the slider with
the set-screw hole at the bottom of the support tube. Insert the set-screw
into the hole to lock the slider in place (1c). Tighten the set-screw
completely, then loosen it by a maximum 1-quarter turn and check the
operation of the arm joint.
Check: Set-screw has to be flush.
Detailed view 2
e Place the O-ring and the ceiling cover over the support tube. Insert the
support tube into the anchor plate and fix it temporarily, using supplied
bolts (see detailed view 2). Align the support tube to the direction of the
fixture’s general usage. Tighten the screws on the anchor plate. Now
connect to the electrical power supply, as per the wiring diagram (see
sheet enclosed with the set of bolts). Slide the ceiling cover and the O-ring
upwards.
f Head Assembly (see page
6
8)
Before mounting the MIRA 45 Single Ceiling, take heed of the operating range.
Note: Only qualified technicians should carry out MIRA 45 installation.
Two people are required for assembling the MIRA 45 Single Ceiling. The supply voltage
must correlate with the voltage noted on the fixture’s rating label. The ceiling fitting is
to be used exclusively at ceilings that are either solid, or supplied with a suitable high-
strength ceiling-mounting solution.
1. Drill holes in accordance to the enclosed drilling template (Ø=8 mm; depth=55
mm). Clean out the drilled holes. Attach the anchor plate using the four anchor
bolts. Tap the anchor bolts completely in, using a hammer. Tighten the nut with an
open-ended wrench (approx. 3-4 turns, 23Nm torque).
2. Perform this Step on a flat and level surface. Pull the cable through the support
tube. Insert the slider into the groove of the arm joint, noting the location of the
fixing hole (see detailed view 1 part ‘a’). Slide the arm and support tube together
(view 1, direction ‘b’). Align the hole in the slider with the set-screw hole at the
bottom of the support tube. Insert the set-screw into the hole to lock the slider
in place (1c). Tighten the set-screw completely, then loosen it by a maximum
1-quarter turn and check the operation of the arm joint. Check: Set-screw has to
be flush.
3. Place the O-ring and the ceiling cover over the support tube. Insert the support
tube into the anchor plate and fix it temporarily, using supplied bolts (see detailed
view 2). Align the support tube to the direction of the fixture’s general usage.
Tighten the screws on the anchor plate. Now connect to the electrical power
supply, as per the wiring diagram (see sheet enclosed with the set of bolts). Slide
the ceiling cover and the O-ring upwards.
4. Head Assembly (see page 68) Before mounting the MIRA 45 Single Ceiling, take
heed of the operating range.
Assembly and Installation MIRA 45 Single Ceiling
Before mounting the MIRA 45 Single Ceiling, take
heed of the operating range.