Connect discharge hose (optional) – BE Pressure supply 2" Fire Fighting Cart HPFC-2070R User Manual
Page 12
12
assembly
9
3.
Slide
hose
clamp
(A
) over
end
of
hose
(B
).
Slide
suction
hose
onto
hose
barb
(C
).
Tighten
hose
clamp
securely
using
a
standard
1/4”
(6mm)
screwdriver.
Attach
Suction
Hose
to
Strainer
Basket
Slide
hose
clamp
over
hose.
Attach
open
end
of
suction
hose
to
strainer
hose
barb.
Tighten
hose
clamp
securely
using
a
standard
1/4”
(6mm)
screwdriver.
Connect
Discharge
Hose
(Optional)
If
desired,
use
a
commercially
available
hose.
DO
NOT
use
a
hose
with
an
inside
diameter
smaller
than
the
pump’s
discharge
port
size.
1.
Slide
barb
cuff
over
hose
barb.
Insert
rubber
seal
into
end
of
barb
cuff
as
shown
earler.
2.
Screw
hose
barb
assembly
onto
pump
in
clockwise
rotation
until
hose
barb
assembly
is
tightened
securely.
3.
Slide
hose
clamp
over
end
of
discharge
hose.
Slide
discharge
hose
onto
hose
barb.
Tighten
hose
clamp
securely
using
a
standard
1/4”
(6mm)
screwdriver.
C
A
B
Your water pump requires some set up and is ready for use after it has
been properly serviced with the recommended oil and fuel.
If you have any problems with the set up of your water pump, please call
the pressure washer help line at 1-866-850-6662 If calling for assistance,
please have the model and serial number from the data tag available.
Connect Suction Hose to Pump
1. Slide hose clamp (A) over end of hose (B). Slide suction hose onto
hose barb (C). Tighten hose clamp securely to the hose.
9
3. Slide hose clamp (A) over end of hose (B). Slide
suction hose onto hose barb (C). Tighten hose clamp
securely using a standard 1/4” (6mm) screwdriver.
Attach Suction Hose to Strainer Basket
Slide hose clamp over hose. Attach open end of suction hose
to strainer hose barb. Tighten hose clamp securely using a
standard 1/4” (6mm) screwdriver.
Connect Discharge Hose (Optional)
If desired, use a commercially available hose. DO NOT use a
hose with an inside diameter smaller than the pump’s
discharge port size.
1. Slide barb cuff over hose barb. Insert rubber seal into
end of barb cuff as shown earler.
2. Screw hose barb assembly onto pump in clockwise
rotation until hose barb assembly is tightened securely.
3. Slide hose clamp over end of discharge hose. Slide
discharge hose onto hose barb. Tighten hose clamp
securely using a standard 1/4” (6mm) screwdriver.
C
A
B
B
A
C
Attach Suction Hose to Strainer basket
1. Slide hose clamp over hose. Attach open end of suction hose to
strainer hose barb. Tighten hose clamp securely.
Connect Discharge Hose (Optional)
If desired, use a commercially available hose. DO NOT use a hose with
an inside diameter smaller than the pump’s discharge port size.
1. Slide barb cuff over hose barb. Insert rubber seal into end of barb cuff
as shown earlier.
2. Screw hose barb assembly onto pump in clockwise rotation until hose
barb assembly is tightened securely.