Bering Optics Rubicon Reflex Sight - Manual (Page 2)

Instructions
MOUNTING
1. Your RUBICON Reflex Sight will fit any
standard Weaver, Picatinny or MIL-STD-
1913 style base. Be sure to check that
your mounting base (not included) is
installed correctly and is securely
fastened to the gun prior to mounting the
sight.
2. Loosen the side bolt on the sight mount.
Position the sight mount on your base
rail, so that the cross bolt engages one of
the slots on the base. Hand tighten the
side mount bolt.
3. The sight has unlimited eye relief,
however you will need to allow a
minimum of three inches of clearance
between the end of the sight and your
eye when in the shooting position. Go
ahead and tighten the side mount bolt
once you have the correct clearance.
OPERATION AND ZEROING
1. Remove the protective cover.
2. Push the front ON/OFF/brightness
control button, which is activates the unit.
3. Repeatedly pressing the ON/OFF/
brightness control button, set the desired
level of the reticle brightness.
4. Start by sighting along the barrel and aim
at a target 25 to 50 yards away. View
through your reflex sight and align the ed
dot with the target as seen along the
barrel.
WARNING: BEFORE MOUNTING YOUR NEW SIGHT, BE SURE THAT THE FIREARM IS NOT LOADED! MAKE SURE TO PRACTICE SAFE FIREARM
HANDLING PROCEDURES AT ALL TIMES.
5. Fire a few test shots to determine the point of
impact of your weapon. If you are not hitting your
aiming point (the center of the target), follow the
instructions listed in Step 4 to make the windage or
elevation adjustment needed. The below table
shows the proper amount of adjustment necessary
depending upon the range at which you are
shooting.
6. To make windage adjustments, locate the
Windage/Elevation adjustment wheel and the
adjustment screwdriver that came with your sight.
For windage adjustments, insert the screwdriver
through the center of the Windage/Elevation
adjustment wheel then into the slot of the screw
head, located on the side panel of the sight. To
make elevation adjustment,
insert the screw driver into the
slot of the screw head,
located on the top panel of
the tail of the sight. The below
table shows the proper
amount of adjustment
necessary depending upon
the range at which you are shooting.
7. To switch the unit OFF, push and hold the front
button for two seconds.
REPLACING THE BATTERY
1. To install a new CR2032 (3V) “coin-style” battery,
unscrew two hex bolts on the top panel of the
sight. (Using the included Hex Wrench)
2. Remove the top section of the reflex sight.
Remove the old battery and insert the new battery
(+ side up.). Replace the top section and tighten
the hex bolts.
Distance, yds. One full revolution of Windage/
Elevation screws
25 12.5”
50 2.5”
100 50”
3. When the battery is replaced, re-zeroing
is recommended.
STORAGE
Always store the unit with the protective plastic
cover on, in a dry well ventilated space in
temperature above +15°C (60° F). Do not store
near heating devices. Do not store in direct
sunlight or high humidity conditions (higher
than 70 %). Remove the battery for prolonged
storage.
LIMITATION OF LIABILITY
The manufacturer will not be liable for any
claims, actions, suits, proceedings, costs,
expenses, damages or liabilities arising from
the use of this product. Operation and use of
the product are the sole responsibility of the
user. The provision of products sold and
services performed by manufacturer to the
user shall not be interpreted, construed, or
regarded, either expressly or implied, as being
for the benefit of creating any obligation toward
any third party of legal entity outside
manufacturer and the user. The remedies of
the purchaser set forth herein are exclusive
and the total liability of manufacturer shall not
exceed the purchase price of the unit. The user
is solely responsible to comply with local and
national laws regarding use of this product. In
no event shall manufacturer be liable for
consequential, incidental, special or other
damages.