Cooper Instruments & Systems DFI INFINITY Digital Force Indicator/Controller User Manual
Dfi infinity strain meter/controller user’s guide
Advertising
Table of contents
Document Outline
- NOTES, WARNINGS AND CAUTIONS
- 1.0 INTRODUCTION
- 2.0 UNPACKING
- 3.0 SAFETY CONSIDERATIONS
- 4.0 PARTS OF THE METER
- 5.0 SETUP
- 6.0 JUMPER POSITIONS
- 7.0 SIGNAL AND POWER INPUT CONNECTIONS
- 8.0 METHODS FOR SCALING THE METER TO DISPLAY IN ENGINEERING UNITS
- 9.0 LOCKOUT CONFIGURATIONS AND METER FUNCTION MENUS
- 9.1 Individual Lockout Information
- 9.2 Meter Function Menus
- 9.2.1 INPUT
- 9.2.2 RDG.CNF (READING CONFIGURATION)
- 9.2.3 RDG SC (Reading Scale) AND RDG OF (Reading Offset)
- 9.2.4 IN CNF (Input Configuration)
- 9.2.5 IN.SC.OF (Input Scale And Offset)
- 9.2.6 DEC PT (Decimal Point)
- 9.2.7 CNT BY (Count By)
- 9.2.8 FIL.CNF (Filter Configuration)
- 9.2.9 FIL TI (Filter Time Constant)
- 9.2.10 SP CNF (Setpoints 1 & 2 Configuration)
- 9.2.11 AL CNF (Alarm Configuration)
- 9.2.12 AL FNC (Alarm Function)
- 9.2.13 AL RDG (Alarm Readings)
- 9.2.15 AL DB (Alarm Deadband)
- 9.2.16 OUT.CNF (Output Configuration)
- 9.2.17 OT.SC.OF (Output Scale And Offset)
- 9.2.18 BAUD (Baud Rate)
- 9.2.19 SERCNF (Serial Communication Configuration)
- 9.2.20 ADDRESS (Multipoint Communications Device Address)
- 9.2.21 DAT FT (Data Format)
- 9.2.22 BUS FT (Bus Format)
- 9.2.23 SERCNT (Serial Count)
- 9.2.24 Analog Output Calibration Numbers
- 10.0 SETPOINTS/ALARMS
- 10.1 Features Overview
- 10.2 Unlocking The Features
- 10.3 Selecting SP CNF Setpoint Configuration Features
- 10.4 Deviation Function For Alarms
- 10.5 Selecting AL CNF Alarm Configuration Features
- 10.6 Selecting AL FNC Alarm Function Features
- 10.7 AL RDG: Alarm Readings-Select Delay In Alarm Action
- 10.8 SP DB: Select “SP 1” and “SP 2” Deadband \(
- 10.9 AL DB: Select Alarm 1 (SP 3) and Alarm 2 (SP 4) Deadband (Hysteresis)
- 10.10 OUT .CNF: Control Flashing Of The Display
- 10.11 Entering Setpoint Levels (In Run Mode)
- 11.0 PEAK AND VALLEY READINGS
- 12.0 ANALOG OUTPUT OPTION
- 13.0 BCD OPTION
- 13.1 Features Overview
- 13.2 BCD Card Jumper Table
- 13.3 Interconnect Board
- 13.4 50-Line Cable Compatibility
- 13.5 Selecting The Source Of BCD Data: “OUT .CNF”
- 13.6 Hold Control
- 13.7 Data Ready Timing Pulses
- 13.8 Bringing Out The BCD Overflow Line
- 13.9 3 Digit At A Time Multiplex
- 13.10 6 Digit At A Time Card Address
- 13.11 Select Data Polarity: Jumper S8
- 13.12 Decimal Point Address Code
- 13.13 Applying Non-Isolated/Isolated Power
- 13.14 Driving A Printer
- 14. RELAY OPTIONS
- 15.0 RS-232 OR RS-485 OPTION BOARD
- 16.0 EXTERNAL CONTROL LINES
- 16.1 Tare (PIN 1)
- 16.2 Peak (PIN 2)
- 16.3 Valley (PIN 3)
- 16.4 SWLIN2 (PIN 4)
- 16.5 Peak & Valley Or External Reset (PIN 5)
- 16.6 Push To CAL (PIN 6)
- 16.7 Digital Ground (PIN 7)
- 16.8 +5 V (PIN 8)
- 16.9 Display Hold (PIN 9)
- 16.10 Lockout EEPROM \(And ‘MENU’ Button\) \(
- 16.11 Print Command And/Or Reset Of Alarms (PIN 11)
- 16.12 Nonstandard RX (PIN 12) And Nonstandard TX (PIN 13)
- 16.13 Push to CAL (PIN 14)
- 16.14 +V EXT (PIN 15)
- 16.15 SP1 (PIN 16)
- 16.16 SP2 (PIN 17)
- 16.17 AL1 (PIN 18)
- 16.18 AL2 (PIN 19)
- 16.19 RTN EXT (PIN 20)
- 17.0 TROUBLESHOOTING - DISPLAY MESSAGES AND TROUBLESHOOTING GUIDE
- 17.1 Error Mode Messages
- 17.1.1 Flashing 999999 (Numerical Overflow)
- 17.1.2 Flashing ERR O1 (Offset Overflow)
- 17.1.3 Flashing ERR O2 (Setpoint Overflow)
- 17.1.4 NOSTOR & STORED (Programming Entries In EEPROM)
- 17.1.5 Flashing +OVLD (Positive Input Overload)
- 17.1.6 Flashing +OPEN (Open Sensor Indication)
- 17.1.7 Flashing -OPEN (Open Sensor Indication)
- 17.1.8 Flashing I OVSC (Input Overscale)
- 17.1.9 Flashing R OVSC (Reading Overscale)
- 17.1.10 Flashing CB OVF (Count By Overflow)
- 17.1.11 Flashing UOM.OVF (Unit Of Measure Overflow)
- 17.2 Troubleshooting Guide
- 17.1 Error Mode Messages
- 18.0 SPECIFICATIONS
- 19.0 FACTORY PRESET VALUES
- 20.0 RECORD YOUR SETUP VALUES
- WARRANTY REPAIR POLICY