Integra LifeSciences Laparoscopic Instrument Care and Cleaning - Manual (Page 4)

4
PART 2 - LAPAROSCOPIC SURGICAL
HAND INSTRUMENTS
for medical use
IMPORTANT – PLEASE READ CAREFULLY BEFORE USING
Indications for use:
Miltex ® laparoscopic surgical hand instruments have specific
indications for use and the user should appropriately decide
whether the instrument is suitable for the desired application.
Miltex cannot provide any warranty for results due to
incorrect application.
These instructions are applicable to Miltex ® laparoscopic
instruments and should be followed to prevent damage to
instruments. Damage resulting from instrument misuse and
improper care may void the product warranty.
Optimal function of the instruments and longer service life can
be achieved when the following instructions are observed:
• Follow instructions for proper cleaning and care of your
instruments.
• Handle the instruments with care.
• Avoid contact with other electrosurgical instruments
during use. This could result in damage to the protective
insulation coating.
• Do not bend or kink instrument sheaths.
• Make sure that insulation of instruments is not damaged
via sharp edges or other instruments during use and
during cleaning and sterilization.
• Do not drop instruments or hit against hard surfaces.
• Check function of joints and connectors regularly. Use
instruments only for the surgical purpose for which they
have been designed.
• Avoid excessive force on the instruments.
• Laparoscopic instruments should only be used by trained
and authorized personnel.
• Sterilize before use. This instrument is not provided sterile.
Stainless steel and temperature resistant plastic materials are
used in the manufacture of laparoscopic surgical instruments.
Silicone rings and washers are used as seals on sheaths and
other components.
INSTRUCTIONS FOR CARE & CLEANING OF
MILTEX ® ENDOSCOPES AND LAPAROSCOPIC
SURGICAL HAND INSTRUMENTS
Instructions for Use/English
1. CLEANING
Immediately after each use and to prevent residual proteins
from drying on instruments, instruments should be fully immersed
in appropriate neutral-pH cleaning and disinfecting solution
recommended for reprocessing of laparoscopic surgical instruments.
Closely follow the cleaning and disinfectant manufacturer
instructions for chemical concentration and immersion time
recommendations. Plain water washing is not considered
adequate. It is recommended that fresh solutions be used
every day. Higher concentration and prolonged immersion time
may cause corrosion or other damage to the instruments.
Always avoid overnight or weekend holding or soaking.
Manual Disinfection and Cleaning:
For Manual Disinfection and Cleaning, use a soft nylon brush to
gently remove any exterior dirt and debris. Instruments are
equipped with a LUER-LOCK connection which should be
opened and force flushed using the appropriate equipment and
pressure flushing system. A water jet gun should be used on
the jaws, joints, handles and the inside of sheaths. After
cleaning and disinfection, the instruments should be
thoroughly rinsed, both on the exterior and interior sheath, with
distilled water. Immediately dry instruments to prevent
corrosion. Drying can be performed manually, but a compressed
air pistol is recommended for more delicate instruments and is
more effective for overall drying.
Thoroughly inspect instruments for effective cleaning (free
from any visible dirt and residue). Also inspect the
instruments for any damaged, worn, corroded, pitted/porous
conditions and ensure proper function. Contact Miltex if
damage is observed and if repair is necessary. Apply
non-silicone instrument lubricant (such as Miltex REF 3-700
Instrument Spray Lube) to the joints and jaws of the instrument
to ensure easy movement. Caution: Do not oil electrical
connections on instruments.
Machine/Mechanical Disinfection and Cleaning:
For Machine/Mechanical Disinfection and Cleaning, follow
equipment manufacturer’s instructions carefully. Instruments
should be stored in carriers or fixed in suitable trays which are
intended for cleaning and to prevent movement during instrument
processing. Instruments with jaws such as forceps, graspers,
scissors, dissectors and needle holders must have the jaws in
an open position before cleaning. Instruments equipped with
a LUER-LOCK connection should be opened and force
flushed using the appropriate equipment and pressure flushing
system. Distilled water is recommended to be used as the
final rinse to avoid water staining and corrosion on the instrument.
Follow equipment manufacturer’s drying cycle recommendations.
It is recommended that the interior sheath be further manually
dried via compressed air pistol to ensure effective
internal drying.