Crestron electronic CLX-1DELV4 - Manual

Connections via CLT terminal block (sold separately)
LINE: (1) DIN rail terminal block, black, line power input
DIM 1 - 4: (4) DIN rail terminal blocks, red, channel outputs
N IN: (1) DIN rail terminal block, white, line input neutral
N OUT 1 - 4: (4) DIN rail terminal blocks, white, channel output neutrals
Buttons
SETUP: Used for manual channel activation and TSID
LED Indicators
PWR: (green) Indicates line power is applied to the LINE terminal
NET: (yellow) Indicates communication with the control system
1 – 4: (red x4) Indicates state of each channel
SETUP: (red) Indicates unit is in setup/manual mode
Environmental
Temperature: 32° to 104°F (0° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 20 BTU/Hr + (7.5 BTU/Hr x Load Current in Amps), 140 BTU/Hr at
maximum load
Enclosure
Gray metal with black heat sink, surface mount module with (2) integral mounting flanges,
occupies 1 module space in any CAEN enclosure
Dimensions
Height: 7.59 in (19.27 cm)
Width: 6.92 in (17.57 cm)
Depth: 3.43 in (8.70 cm)
Weight
3.00 lb (1.36 kg)
AVAILABLE ACCESSORIES
CAEN Automation Enclosures
CLT-1DELV4 Terminal Block
www.crestron.com | 800.237.2041
> 4 channels of dimming for electronic low-voltage and
incandescent loads
> Single 120 Volt feed
> Air-gap relays on every channel output
> Override preset capability
> Convection cooled
> Occupies 1 module space in a CAEN automation enclosure
> Easy termination using CLT-Series terminal block
As part of a complete Crestron lighting system, the CLX-1DELV4 lighting control
module provides 4 channels of dimming for electronic low-voltage and
incandescent loads. Each channel is rated for 1200 Watts, with a total module
rating of 1920 Watts. Air-gap relays are provided on every channel output allowing
individual circuits to be serviced without disabling the entire module.
CLX-Series dimmers are rigorously built using oversized heat sinks for ultimate
reliability. Split-bobbin transformers and ground referenced electronics deliver
superior performance. Lamp flicker is minimized through Crestron’s innovative
zero-crossing detection technique backed by proprietary firmware.
Low-maintenance convection cooling assures quiet and trouble-free operation.
An override feature allows each channel to be adjusted to a preset state during
setup. In the event that Cresnet communications should be disrupted for any
reason, a simple contact closure can be used to activate the override presets on a
global or semi-global basis.
The CLX-1DELV4 occupies a single module space in any CAEN automation
enclosure. Termination of high-voltage wiring to the module is facilitated by a
CLT-1DELV4 terminal block, sold separately to enable termination of the wiring
anytime prior to installing the module. CLX modules are controlled by the PAC2
and PAC2M professional automation control systems via the Cresnet network. A
5-wire link provides bussing of the Cresnet and override signals between modules
within an enclosure (interconnect jumpers included).
SPECIFICATIONS
Load Ratings
Dimmer Channels: 4
Per Channel: 10 Amps (1200 Watts)
Module Total: 16 Amps (1920 Watts)
Load Types: Electronic Low-voltage, Incandescent
Power Requirements
120 Volts AC, 60Hz, single-phase
Connections on module
Module Interconnect: (2) 5-pin 0.156 inch headers, Cresnet/Override interconnect ports
Connect to PAC2, PAC2M, CAEN-BLOCK, or adjacent CLX-Series module using interconnect
cable provided
Specifications subject to change without notice. Doc.4840 12/07
©2007 Crestron Electronics, Inc. All brand names, product names and trademarks are the property of their respective owners.
Crestron Electronics, Inc. 15 Volvo Drive l Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 l Fax: 201.767.1903
Crestron CLX-1DELV4
4 Channel Electronic Low-
Voltage Dimmer Module
Shown with CLT-1DELV4 Terminal Block