Channel Vision 2-Door Telephone Entry Controller P-0921 - Manual (Page 5)

TELCO
2-DOOR TELEPHONE
ENTRY CONTROLLER
INPUT
OUTPUT PAGE DOOR 2 POWER DOOR 1
PRO
C H A N N E L
TM V I S I O N
C H A N N E L
V I S I O N TM
Model
P-0921
T
E
L
C
O
IN
P
U
T
CO / No CO
# / *
T
E
L
C
O
O
U
T
P
U
T
D
O
O
R
2
D
O
O
R
1
C
H
IM
E
2
C
H
IM
E
1
U
N
L
O
C
K
D
O
O
R
2
U
N
L
O
C
K
D
O
O
R
1
A
U
X
Strike
power
supply
To Strike
Mechanism
5
Basic Setup & Operation
When the button is pressed on the door-intercom, the phones in the house
will ring. If a doorbell chime and transformer are connected to the CHIME
contact, the doorbell chime will also be heard.
If the phone is answered within 20 seconds, it will be automatically
connected to the door-intercom. If the phone is answered after 20 seconds
simply press ## (or **) to be connected.
(Note: the activation key is determined by the switch labeled “# or *”)
While speaking to the door-intercom, the STRIKE 1 contact can be
activated by pressing #71 (or *71).
The Unlock Door terminals can be momentarily shorted with a simple push
button which will activate the strike without the use of a telephone.
To send a whole-house page from any phone, press #5 (or*5).
(see the following page for a full list of user codes).
House
Telephones Channel Vision Compatible
Door Intercom Station
To Whole-House
Paging System
Telephone
Service
4
Doorbell
Chime
and
Transformer
Examples: (assuming the P-0921 is set for # operation)
The user dials ## - they will be connected to the last door station that was
activated. Pressing ## again will toggle to the other door.
The user dials ###1 - they will be connected to DOOR 1
(Then, while talking)
The user dials #71 - strike 1 will be activated.
The user dials ###2 - they will be connected to DOOR 2
(Then, while talking)
The user dials #72 - strike 2 will be activated.
User Codes
Call Waiting functions
User codes for P-0921
Replace x with # or * depending on the position of the #/* switch.
Key codes Function
xxx1 Talk with DOOR 1
xxx2 Talk with DOOR 2
xx When on a phone call: places call on hold & answers door -press again to go back
When not on a phone call: answers the last door station activated
x5 Activate page out function
(the following codes work while you talk to the door)
x71 Activate STRIKE 1 (can use AUX terminals or TE110DS module)
x72 Activate STRIKE 2 (Requires TE110DS module)
Situation: Doorbell is pressed when you are already on the phone.
You will hear: You will hear call waiting beeps, press ## (or **) to be
connected.
Situation: You have placed the caller on hold and switched to the door
intercom.
You will hear: Occasional beeps reminding you that a call is holding.
Situation: You are speaking to the door intercom when an incoming phone
call is detected by the system.
You will hear: Beep, beep, pause... Beep, beep, pause... etc.
Situation: The doorbell is pressed at the same time as an incoming call is
detected.
When you pick up the receiver: you will be connected to the incoming call.
You will hear: Beeps corresponding to the distinctive ring for the door
intercom being activated.
Simple push button (optional)