Dell S320 Projector User Manual
Page 7
pdmAudio
pdmAudioBalanc
e
.1.3.6.1.4.1.2699.2.4.1.16.6.0
Integer R
DEFVAL { 0 }
pdmAlert pdmAlertIndex
1.3.6.1.4.1.2699.2.4.1.18.1.1.1.1
Integer not-accessible 1
pdmAlert
pdmAlertGroupT
ype
1.3.6.1.4.1.2699.2.4.1.18.1.1.2.1
String
R
See Note 1
pdmAlert
pdmAlertGroupI
d
1.3.6.1.4.1.2699.2.4.1.18.1.1.3.1 String
R
See
Note
1
pdmAlert
pdmAlertCode
1.3.6.1.4.1.2699.2.4.1.18.1.1.4.1
String
R
DEFVAL { "" }
pdmAlert
pdmAlertDescrip
tion
1.3.6.1.4.1.2699.2.4.1.18.1.1.5.1 String
R
Alert's condition has lamp
Fail, Lamp hours running out,
Projector Overheating, Lamp
Overheating and Fan Error.
pdmAlert
pdmAlertSeverity
Level
1.3.6.1.4.1.2699.2.4.1.18.1.1.6.1
Integer R
See Note 1
pdmAlert
pdmAlertTrainin
gLevel
1.3.6.1.4.1.2699.2.4.1.18.1.1.7.1 Integer R
DEFVAL { 2 }
pdmAlert
pdmAlertDateTi
me
1.3.6.1.4.1.2699.2.4.1.18.1.1.8.1
String
R
DEFVAL
{ "1980-01-01T00:00:00" }
pdmAlert
pdmAlertPowerO
nCount
1.3.6.1.4.1.2699.2.4.1.18.1.1.9.1
String
R
DEFVAL { "" }
pdmAlert
pdmAlertSysUpti
me
1.3.6.1.4.1.2699.2.4.1.18.1.1.10.1
String
R
DEFVAL { "" }
pdmAlert
pdmAlertCritical
AlertsCount
1.3.6.1.4.1.2699.2.4.1.18.2.0 Integer R
pdmAlert
pdmAlertAllAlert
sCount
1.3.6.1.4.1.2699.2.4.1.18.3.0
Integer R
Note 1:
a) If there is no any current alert, all of OID in alert table will respond default value.
pdmAlertGroupType =” “
pdmAlertGroupID = 0
pdmAlertSeverity = other (1)
The reset Object will respond default.
b) If there is FAN alert happen, the tables is shown below.
pdmAlertGroupType =” Fan”
pdmAlertGroupID = “Fan Error”
pdmAlertSeverity = Critical (3)
The rest Object will respond default.
c) If there is Lamp fail alert happen, the tables is shown below.
pdmAlertGroupType = “Lamp”
pdmAlertGroupID= Lamp Fail
pdmAlertSeverity = Critical (3)
The rest Object will respond default.
d) If there is Lamp hours running out alert happen, the tables is shown below.
pdmAlertGroupType = “Lamp”
pdmAlertGroupID= Lamp hours running out
pdmAlertSeverity = warning (4)
The rest Object will respond default.
e) If there is Projector Over-heating alert, the tables is shown below.
pdmAlertGroupType = “ThermalSensor”
pdmAlertGroupID= “Projector Overheating”
pdmAlertSeverity = warning (4)
The rest Object will respond default.
f) If there is Lamp Over-heating alert, the tables is shown below.
pdmAlertGroupType = “ThermalSwitch”
pdmAlertGroupID= “Lamp Overheating”
pdmAlertSeverity = Critical (3)
The rest Object will respond default.
Information in this document is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or
their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
September 2012 Rev. A00