Vermont Casting Non-Catalytic Convection Heater 2478CE - Manual (Page 22)

22
Dutchwest Non-Catalytic Convection Heater
30003850
is worse if the chimney is located outside the home or
if the chimney flue has a cross-sectional volume much
larger than the stove outlet.
Steel Chimney
Most factory-made ‘Class A’ steel chimneys have a
layer of insulation around the inner flue. This insulation
keeps the smoke warm and protects the surrounding
structure from the high flue temperatures. Because the
insulation is less dense than masonry, the inner steel
liner warms up more quickly than a masonry chimney;
this makes the steel chimney support a good draft more
quickly than masonry does. Steel chimneys are not as
attractive as masonry, but they are very durable and
generally outperform masonry.
Indoor/ Outdoor Location
Because the chimney’s function is to keep the smoke
warm, it is best to locate it inside the house. This loca-
tion uses the house as insulation for the flue and allows
some radiant heat release from the flue into the home.
Since an interior chimney doesn’t continuously lose its
heat to the outdoors, less heat from the stove is re-
quired to get it warm and keep it warm.
Flue Sizing
The flue size for a controlled-combustion appliance
should be based on the cross-sectional volume of the
stove flue outlet. In this case, more is definitely not bet-
ter. Hot gases lose heat through expansion; if a stove
with a six-inch flue collar (181 sq cm [28 square inch]
area) is vented into a 254 x 254 mm (10” x 10”) flue, the
gases will expand to over three times their original vol-
ume. As gases cool with expansion, draft strength de-
creases. If an oversized flue is also outside the house,
the heat it absorbs will be conducted to the outdoor air
and the flue will remain relatively cool.
It is common for a masonry flue to be oversized for the
stove. Such a chimney can take quite a while to warm
up and the stove performance will likely be disappoint-
ing. The best solution to an oversize flue problem is
the installation of an insulated steel chimney liner of
the same diameter as the appliance flue outlet. The
liner keeps the exhaust gas warm and the result is a
stronger draft. An uninsulated liner is a second choice
- although the liner will keep the exhaust restricted to its
original volume, the air around the liner will require time
and heat energy to warm up.
Check your local codes. You may be required to install
a flue liner in any oversize or masonry flue.
Pipe & Chimney Layout
Every bend in the flue will act as a brake on the exhaust
as it flows from the firebox to the chimney cap. The
ideal pipe and chimney layout is straight up from the
stove through a completely straight chimney. Use this
layout if at all possible as it will promote optimum stove
performance and simplify maintenance.
If the stovepipe must elbow to enter a chimney, locate
the elbow about midway between the stove top and
the chimney thimble. This configuration lets the smoke
speed up before it must turn, keeps some pipe in the
room for heat transfer, and allows long-term flexibility
for installing a different appliance without relocating the
thimble.
There should be no more than eight feet of single-wall
stove pipe between the stove and a chimney. Longer
runs can cool the smoke enough to cause draft and cre-
osote problems. Use double-wall stove pipe for longer
runs.
Single Venting
Your stove requires a dedicated flue. Do not connect
the stove to a flue used by any other appliance. Chim-
ney draft is a natural form of energy and follows the
path of least resistance. If the stove is vented to a flue
that also serves an open fireplace or another appliance,
the draft will also pull air in through those avenues.
The additional air flow will lower flue temperatures,
reduce draft strength and promote creosote develop-
ment; overall stove performance will suffer. The effect
is similar to that of a vacuum cleaner with a hole in the
hose. In some extreme instances, the other appliance
can even impose a negative draft and result in a dan-
gerous draft reversal.
Fuel
Even the best stove installation will not perform well
with poor fuel. If available, always use hardwood that
has been air-dried (“seasoned”) 12-18 months. Soft-
wood burns more rapidly than hardwood and has a high
pitch content that can result in creosote. Decayed wood
of any type has little heat value and should not be used.
Unseasoned (‘green’) wood has a high moisture con-
tent. Much of its heat value will be used to evaporate
moisture before the wood can burn. This significantly
reduces the amount of energy available to warm your
home, as well as the intensity of the fire and tempera-
ture of the exhaust gas. Incomplete combustion and
cool flue temperatures promote creosote formation and
weak draft.
You can judge the moisture content of wood by its ap-
pearance and weight or use a commercially available
moisture meter for an exact measurement. Unseasoned
wood will be a third heavier than dry wood. Also, look
for cracks (“checking”) in the ends of the log that result
from contraction as the wood dries. The longer and
wider the cracks are, the dryer the wood is.