Chamberlain 40 User Manual

Page 2

Advertising
background image

© 2006, Chamberlain Group Inc.

114A1137C

All Rights Reserved

NOTE: If your garage has a built up jamb, drill the hole 2" deep.
Then, on inside edge of jamb, drill a second hole into first hole to
complete access.

STEP 2:

Hold keyboard firmly with the back of the case UP.

Position thumb against bottom of case and pull up sharply.
Keyboard will lift out of cover, allowing access to bottom
mounting hole.

Guide the keyboard cable through hole to inside the garage.
Position the keyboard against outside jamb. Drill two 1/8" pilot
holes for fastening screws. Attach securely with (2) 6ABx1-1/4"
screws. Close cover.

Excess cable can be folded and inserted into the access hole to
keep it out of the way.

STEP 3:

Connect the 2-strand bell wire to terminals labeled 1

and 2 on back of console. Insert keyboard cable connector into
slot on side of console. Be sure connector guides are facing
BACK of console.

IMPORTANT: Some garage door openers have a third screw
terminal which supplies power to the radio control. This terminal
can be connected to terminal No. 3 on the console with a third
strand of bell wire (not supplied).

With any garage door opener made by Stanley, accessory
Transformer 95 MUST be Installed.

TRANSFORMER INSTALLATION INSTRUCTIONS

Connect one end of the 2-strand bell wire supplied with the kit to
each of the transformer terminals (no polarity). Connect the other
end of bell wire to terminals 1 and 3 on the Keyless Entry
console.

I

f this accessory is used with any garage door opener other than

Sears or Chamberlain and the battery fails in two months,
transformer must be installed. Follow Instructions above.

STEP 4:

Position console on an interior garage wall

approximately one foot from outside edge of door. Fasten
with (2) screws provided.
Run bell wire up wall and across ceiling to garage door
opener terminals. Use insulated staples to secure wire. On
current line Chamberlain models, connect wire to red and
white opener terminals. On older models, connect to
terminals used for push button controls. Cut off any excess
wire. Connect to terminals used for push button
controls.

STEP 5:

Pry open front panel of console with a coin or

screwdriver. Snap a 9 volt battery onto circuit board
connector and drop into console. DO NOT replace panel at
this time.

STEP 6:

To set code, move program/operate switch near

the battery to PROGRAM position (keyboard light should
flash).
NOTE: If the light does not flash, check the cable and
battery connections.
Press any four numbers on keyboard.
CAUTION: For security, do not use address, license or
consecutive numbers (1,2,3,4 etc.).
Move the program/operate switch to OPERATE position
(the keyboard light will go off).
Reconnect power to garage door opener.
NOTE: If you have Installed Transformer Model 95, plug
the transformer Into a 120 VOLT outlet.
Enter the code on the keyboard. If the door operates
properly, replace the front panel on the console.
Loss of power to either the battery or the garage door
opener will not affect the programmed code. However, if
BOTH lose power, the code must be reset.
Battery should produce adequate power for at least one
year. If light In keyboard does not turn on, change the
battery.
NOTE: To maintain the privacy of your code, keep all of
the buttons free from soil. If any of the numbers show
signs of wear, change your code.

1/8" Pilot Hole

1" Dia. Hole
2" Deep

6ABx1-1/4"
Screw

Door
Opening

Cable

Inside
Garage Wall

Inside Edge
of Jamb

Console
Front
Panel

Console
Push Button

Program/Operate
Switch

Batt

ery

PROGR

AM

OPERA

TE

Bell Wire

Transformer
Terminals

Transformer
Model 95

Console
Terminals

To 120V Outlet

Cable

Bell Wire
(To Garage
Door Opener)

Connector
Guides

3

2

1

Advertising
This manual is related to the following products:

65