Qmark GFR Series - Fan-Forced Wall Heaters - Manual (Page 4)

TO INSTALL FAN DECK ASSEMBLY
NOTE: Fan deck assembly should not be installed until after the
drywall phase of construction is complete. Dust from drywall
installation and joint compound can be harmful if it gets inside
fan deck components.
1. Locate fan deck and mounting rails in top of back box.
2. Insert flanges on fan deck into mounting rails and slide back
until fan deck stops (see Figure 6).
3. Make wiring connections, attaching one red and one black
thermostat lead to two (2) black heater leads for 240V or to
black and white heater leads for 120V with wirenuts (provid-
ed). Connect field ground lead to bare ground wire with
wirenut (provided). See Figure 7.
4. Remove 1/2” knockout from grille and install grille using two
oval head screws. Push thermostat knob on thermostat shaft.
5. Reconnect power at main fuse or circuit breaker distribution
panel.
TO CHANGE WATTAGE OUTPUT
The chart shows the wattages available by model. Each heater is
factory wired for its maximum wattage. The last two columns in
the chart refer to the jumpers on the CLIP ‘n’ Fit
® Board. To change
wattage, clip out Jumper 1 and/or Jumper 2 as shown in the chart
below. Completely remove jumpers by clipping at both ends as
close to the board as possible (See Figure 8).
OPERATING
INSTRUCTIONS
1. Heater must be properly installed before operation.
2. After heater is completely assembled, rotate thermostat knob
counterclockwise until control stops. This is the minimum
heat setting.
3. Turn power supply to heater “ON” at main switch panel.
4. Heater should not operate. If it operates disconnect power
and recheck wiring.
5. Rotate thermostat clockwise until it stops (maximum heat set-
ting).
6. Heater and fan should come on. If heater and fan do not
come on, disconnect power and check wiring.
7. Allow heater to continue to operate until room temperature
reaches desired comfort level. Then rotate thermostat knob
counterclockwise slowly until thermostat clicks off.
4
TOP OF BACK BOX
FLANGE ON FAN DECK
MOUNTING RAIL
Figure 6
TABLE 2
TOTAL AMPS
0 thru 12
12.1 thru 16
16.1 thru 24
WIRE SIZE
(COPPER)
#14
#12
#10
CIRCUIT BREAKER
OR FUSE SIZE
15 Amps
20 Amps
30 Amps
TABLE 1
MODEL
R1500FC
R1500T2FC
R2004FC
R2004T2FC
R2404FC
R2404T2FC
VOLTS
120
240
208
240
208
WATT/AMP
1500/12.5
2000/8.3
1500/7.2
2400/10.0
1800/8.7
WATT/AMP
1125/9.4
1500/6.3
1125/5.4
1800/7.5
1350/6.5
WATT/AMP
750/6.3
1000/4.2
750/3.6
1200/5.0
900/4.3
WATT/AMP
375/3.1
500/2.1
375/1.8
600/2.5
450/2.2
WATTAGE
JUMPER
1
JUMPER
2
2400
1800
1200
600
1800
1350
900
450
2000
1500
1000
500
1500
1125
750
375
1500
1125
750
375
Red
Jumper
Leave in
Leave in
Clip out
Clip out
Blue
Jumper
Leave in
Clip out
Leave in
Clip out
R2404FC &
R2404T2FC
@240V @208V
R2004FC &
R2004T2FC
@240V @208V
R1500FC &
R1500T2FC
@120V
SELF HOLD
LIMIT
TEMPERATURE
REGULATOR
Figure 7 - Wiring Diagram
R Series only
RT2 Series only
Figure 8 Clip’n’Fit ® Board