Scarlett SC-1146 - Manual (Page 5)

www.scarlett-europe.com SC-1146 5
GB INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
· Before the first connecting of the appliance check that voltage indicated on the rating label corresponds to the mains
voltage in your home.
· For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described
in this instruction manual.
· Do not use outdoors.
· Always unplug the appliance from the power supply before cleaning and when not in use.
· To prevent risk of electric shock and fire, do not immerse the appliance in water or in any other liquids.
· Close supervision is necessary when it is used near children or invalids.
· Do not leave the appliance switched on when not in use.
· Do not use other attachments than those supplied.
· Do not operate after malfunction or cord damage.
· Do not attempt to repair, adjust or replace parts in the appliance. Check and repair the malfunctioning appliance in the
nearest service center only.
· Keep the cord away from sharp edges and hot surfaces.
· Do not pull, twist, or wrap the power cord around appliance.
· Never attempt to take food or liquid out from the container when the blade is moving. Always wait until the motor stops
completely.
· Do not overload the appliance with a food.
· The appliance operates fast and effective. Do not operate continuously for more than 3 min.
FOOD PROCESSOR ASSEMBLING
· Before the first using, wash all removable parts in warm soapy water, rinse thoroughly and dry. Wipe the housing with a
damp cloth.
· Never immerse motor body in any liquid or wash under running water.
· Place the motor unit on a level surface.
ATTENTION: Never operate processor bowl and blender at the same time.
· Place the bowl and turn it clockwise to the proper position.
· Place blender gear safety lid on the seat, rotating until fixed securely.
ATTACHMENTS
· Use ONLY ONE attachment for food processing.
CUTTING KNIFE\PLASTIC BLADE
· Fit shaft adaptor into the blade (or whip maker) until it fixed securely.
· Fit shaft adaptor on the bowl drive spindle.
· Load products to be processed in the bowl.
· Place lid on the bowl and rotate it to lock.
· Start processing at high speed (position II ).
DISKS - GRATING / SLICING / FRENCH-FRIES
· Set the slicer, grater or french-fries knife in the supporting disc and place it onto shaft adaptor.
· Fit the disk with the spindle onto the blender shaft.
NOTE: you must complete assembling fully; otherwise you cannot switch on device.
FOOD PROCESSOR USING
· Please make sure accessories are at its places before switching on.
· Plug-in device.
PULSE MODE
· Turn the Speeds control switch to PULSE position.
· Before processing cut a food so it would pass through a feeder easily.
· Turn control switch to speed "1" (low speed) or "2" (high speed), so food processor will work continuously until you turn
back to "0" (switch off a speed).
· Gradually feed products to be processed through the feed tube only while processor is operating.
CAUTION: Use the pusher only to feed products, push it evenly and gently. The heavier pressure, the coarser chopping.
CAUTION: Do not operate continuously longer than 3 minutes with less than 1 minute intermission.
· Do not overload the appliance by putting in too much food.
· Do not remove any parts during the operating.
BLENDER
· Leave the processor bowl at the place locked into the slot. Remove shaft adaptor and attachments; do not place food
in the processor bowl.
· or:
· Fit processor lid onto bowl drive shaft and fix it.
· Open blender gear safety cap.
· Place the blender jug onto the blender gear. Make sure it properly fitted.
· Put ingredients into blender jar, and close it with the lid.
· Plug-in, turn the switch/press buttons to recommended speed:
"1"(low speed) for liquid ingredients mainly.
"2" (high speed) for heavier processing, i.e. liquid and solid ingredients mixtures.