Sony RM-V12 - Manual (Page 3)

Step 2: Checking if the Code
Number Works
1 Using the component's original remote control (or
the power switch on the component itself), power
on the component.
2
Aim the RM--V12 Remote
Commander at the component and ( POWER J
press the POWER button.
The component should power off.
3
When the component powers off,
press the POWER button again to
turn it back on. Then check that
the Commander is operating the
other functions of your
component. Press the channel
and volume control buttons.
If the Commander Doesn't
Seem to Be Working...
• First, try repeating these setup procedures using the
other codes listed for your component.
• If - after trying all the codes listed for your
component - you still cannot get the Commander to
work properly, try the search method described
under "Searching for the Correct Code".
If the Commander Seems to Be
Working Properly...
• You're finished setting up the Commander for this
component.
• If you're setting up more than one component (or a
TV/VCR combination), you'll need to complete these
procedures for each component you plan to use with
the Commander.
• Use the label (supplied) to write down the code
numbers of your components. Then affix the label to
the back of the Commander.
Before You Set Up AV...
Before you set up the Commander to operate
component on position AV, you must first define the
type of component you want to use at this position.
To define the type of component you want to use,
complete the following procedure:
1
2
3
Set the slide switch on the
Remote Commander to AV. iflj U llj
Press the POWER button while sleep
pressing the SLEEP button. ^ + (^ power ^
Enter one of the codes from the following table,
based on the type of component you're setting up:
Component Type Code No.
VCR 1
Rcceiver/amp 4
CD player 5
Tape deck 6
TV 8
Cable box 9
For example, if you're .setting up a CD player, you
would press and release 5.
4 Press and release the ENT button
to store the code number in the
Commander's memory.
To finish setting up the component, go to "Step 1:
Entering the Code Number" and complete the
procedures that are described.
you play your audio components through your
receiver (or amplifier).
This feature lets you control the volume of your
components without first having to change the
Commander's slide switch to the component's audio
source.
Factory Preset
Position Audio Plays Through:
CBL TV
TV TV
VCR TV
AV Receiver/amp
For example, to control the volume for vour VCR
programs, vou don't need to change the slide switch
from VCR to TV.
Changing the Factory Preset
Audio Source
If your \’ideo components are connected to an audio
system, voLi probably play your TV and VCR's audio
through your audio receiver, instead of your TV
speakers. If so, you can change the factory preset so
that you can control the volume of your video
components without first having to switch to the
receiver (AV). To change the factory preset audio
source for vour video components, follow the
procedures in "Setting Up a Video Component That's
Connected to an Audio System".
Setting Up a Video Component
That's Connected to an Audio
System
Use the following procedure to change the factory
preset audio source for your video components. You
can change this either before or after you set up the
Commander to u'ork with your component.
1 Set the slide switch on the
Remote Commander to the
position of the video component
that you want to set up.
2
Press the POWER button while J.
pressing the SLEEP button. ^
3
To control the component's
sound through your receiver
which is assigned to AV, press
the VOL - button.
To control the component's
sound through your receiver
which is assigned to TV, press
the VOL + button.
4
Press and release the ENT button
to store your setting in the
Commander's memory.
5
If you haven't already done so, finish setting up
the component by completing the procedures
under "Step 1; Entering the Code Number".
^POWER^
VOL
Using the Remote
Commander
Turning On/Off a Component
1
Set the slide switch on the avcol
Remote Commander to the ^, f--'.