Sony SCT-ID10 - Manual (Page 10)

Looking at the Caller
ID list
The phone stores the data ot the last 20 calls
recei\ ed including "OUT OF AREA" and
"PRIVATE" calls. It keeps track of all calls
recei\ ed; even if they were not ansu ered.
Viewing the Caller ID list
When the phone is not in use, the display shows
the following.
Number of cads which you
have already viewed
Number of calls
which you have
not viewed
-^NEl)j""]2liÓLD 1
You can look through the data in the Caller ID
list to check the number and/or name of the calls
received.
1 Press
The data of the newest call appears for 20
seconds.
SMITH JOHN
7/
2 Press - to display older data or + to
display newer data.
Notes
• If you have not viewed the "NEW 1" data,
other "NEW" data wiW not be counted as the
"OLD" data even after you have viewed them.
• When you have checked all the data by
pressing +, 5 short beeps sound and "TOP OF
LIST" appears.
,
• When you have checked all the data by
pressing 5 short beeps sound and "END OF
LIST" appears. If you press - again, five short
error beeps will sound.
Tip
You can view the Caller ID list during
conversation aFso by following the steps above.
About the "REPEAT" and "SAVE"
display
"SAVE" appears if the call is "saved" (see
below).
SMITH JOHN
7/ H,
HG3
REPEAT" appears if there are more than
two calls from the same caller. The older
data will be replaced by the new data, so the
calls are counted as only one call (for
"NEW" calls only).
Note
If "OUT OF AREA" or "PRIVATE" calls are
made for more than 2 calls, "REPEAT" will be
displayed and only the new data will be
replaced-'
Storing the phone
numbers in the Caller ID
list into speed dialing
buttons
^ Display the phone number you want to
store by pressing + or
2 Press SPEED.
"ENTER 1-5" appears on the display.
3 Press one of the speed dialing numbers
(®to®).
"PRESS PROGRAM" appears on the
display.
4 Press PROGRAM.
You hear a confirmation beep and the
phone stores the number.
Notes
• Do not allow more than 20 seconds to elapse
between each step of the procedure.
• If the phone is connected to a Private Branch
Exchange (PBX), you may need to add an
outside line access digit-
Saving the phone
numbers in the Caller ID
list
As the phono ktvps the data of up to 20 calls, if
21st call comes in, the phono erases the oldest
data automatically.
To pre\ ent important data from being erased,
you can "save" them. The "saved" data will not
be erased until you erase them manually (see
"Erasing the data from the Caller ID list").
N'ou can save up to 10 phone numbers.
1 Search the phone number you want to
save from the Caller ID list by pressing
+ or
2 Press PROGRAM.
You hear a confirmation beep and "SAVE"
appears in front of the phone number.
Note
if you try to save the 11th phone number, you
hear five short error beeps and you cannot save
the phone number. To save another phone
number, erase one of the saved phone number
{see "Erasing the data from the Caller ID list").
Erasing the data from
the Caller ID list
To erase the phone number one by
one
1 First press and then press + or - to
display the phone number you want tc
erase.
2 Press ERASE.
You hear a confirmation beep and the data i
erased.
To erase the entire list at once
1 Make sure that no data or "END OF
LIST" is displayed.
NEÜJ 0 OLD 20
2 Press ERASE.
You hear a confirmation beep and the entire
list is erased.
NEW 0 OLD 0
Notes
• If you try to erase the entire list when there
remains any new calls, you hear five short
error beeps and you cannot erase the list.
• The "saved" numbers (see "Saving the phone
numbers in the Caller ID list") are not erased
even if you erase the entire list. To erase the
"saved" numbers in the Caller ID list, do as
described in "To erase the phone number one
by one."
Using the Caller ID list
You can easily call back a number from the
Caller ID list by pressing the DIAL button.
You can also store a number from the Caller ID
list into one of the the one-touch dialing buttont
Calling back a number from the
Caller ID list
1 First press and then press + or - to
select the number you want to dial.
2 Press DIAL
The phone is set to the ON HOOK
mode and automatically dials the
number displayed.
Note
You can also make a cal) by following the same
procedure after you pick up the h.mdset