Clarion DXZ575USB - Manual (Page 23)

English
21
DXZ575USB
Operations Common to Each Mode
● Setting the clock
2-1. Select “ CLOCK ”.
3-1. Press the [ ] button
3-2. Push the [ SEEK PANEL ] leftward or
rightward to select the hour or the minute.
3-3. Press the [ UP ] or [ DN ] button to set the
correct time.
∗
The clock is displayed in 12-hour format.
3-4. Press the [ ] button to store the
time into memory.
Note:
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the
car’s battery or take out this unit, the clock is
reset. While setting the clock, if another button or
operation is selected, the clock set mode is
canceled.
● Setting the contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “ 7 ”. (Adjustment
level: 1 to 16)
2-1. Select “ CONTRAST ”.
3-1. Press the [ UP ] or [ DN ] button to adjust the
contrast.
● Turning the screen saver function on
or off
This unit is provided with the screen saver
function which allows you to show various kinds
of patterns and characters in the operation
status indication area of the display in a random
order. You can turn on or off this function. If the
button operation is performed with the screen
saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
∗ The factory default setting is “ ON ”.
2-1. Select “ SCRN SVR ”.
3-1. Press the [ UP ] or [ DN ] button to select “ ON ”
or “ OFF ”.
● Entering message information
Message up to 30 characters long can be stored
in memory and displayed as a type of screen
saver setting.
∗
The factory default setting is “ WELCOME TO
CLARION ”.
2-1. Select “ MESSAGE INPUT ”.
3-1. Press the [ ] button.
3-2. Press and hold the [ MENU ] button for 1
second or longer to clear the old message.
3-3. Push the [ SEEK PANEL ] leftward or
rightward to move the cursor.
3-4 Press the [ MENU ] button to select a
character type. Each time you press the
[
MENU ] button, the character type changes
in the following order:
Capital letters ➜ Numbers ➜ Symbols ➜
Capital letters…
3-5. Press the [ UP ] or [ DN ] button to select the
desired character.
3-6. Repeat step 3-3 to 3-5 to enter up to 30
characters for message.
3-7. Press and hold the [ ] button for 2
seconds or longer to store the message in
memory and return to the previous mode.
∗ Press and hold the [ MENU ] button for 1
second or longer to cancel the input
message. Then press and hold the
[
] button for 2 seconds or longer to
store the message and the message return
to the default setting.
To change adjustment setting
1. Press and hold the [ OPTION ] button for 1
second or longer to switch to the
adjustment selection display.
2. Push the [ SEEK PANEL ] leftward or
rightward to select the “item name”.
“ CLOCK ” ↔ “CONTRAST” ↔ “SCRN
SVR” ↔ “MESSAGE INPUT” ↔ “AUTO
SCR” ↔ “SCRL SPD” ↔ “DIMMER” ↔
“BLINKLED” ↔ “A CANCEL” ↔ “TEL SP”
↔ “TEL SW” ↔ “SYSTEM CHECK” ↔
“CLOCK”...
3. Press the [UP] or [DN] button to select the
“desired setting value”.
∗ In the case of display blinking “ENT”, you
can press the [ ] button to adjust
the setting value.
∗ After completing settings, press the
[OPTION] button to return to the previous
mode.
DXZ575USB_EN.book 21 ページ ２００６年１２月２５日 月曜日 午後１２時５７分