Conair TH402 - Manual (Page 2)

Facts You Should Know
Your Thinner ® scale is a precise measuring instrument that is most accurate
when weighing a stationary object. To ensure readings that are 99% accurate,
always try to stand on the same area of the scale platform and DO NOT MOVE.
Should the weight on the scale exceed the scale’s capacity, you may see an
error message ”ERR”.
Electronic sensors are sensitive. Be careful not to drop or jar the scale. Place it
gently onto floor surface, and store where it will be protected from impact.
The scale is an electronic instrument and should never be submerged in water.
Clean with damp cloth and/or glass cleaner.
In the unlikely event that the scale battery malfunctions and needs to be
replaced, lift the battery cover on the bottom of the scale and replace the
old battery with a 3V lithium battery (CR2032). Dispose of the old battery
properly. Do not attempt to open the scale or to remove any components.
Servicing should be done by qualified technicians only. See warranty
information below.
Your personal data has now been entered and stored. User number will
display for 2 seconds, height for 2 seconds, and age for 2 seconds, to confirm
the programming. If any of these data points were set incorrectly, just go
through the customization steps (1–3) again. The scale is now ready for you to
weigh yourself and read body fat and body water measurements.
Using Your Thinner ® Body Fat Monitor
Precautions for Use
CAUTION! Use of this device by persons with any electrical implant such as
a heart pacemaker, or by pregnant women, is not recommended.
1. Tap center of scale platform with foot to activate digital display
(display will flash).
2. Wait for "0.0" to appear in display window.
3. Firmly press the USER button located below the display several times until
your user number appears. Note: The scale will automatically scroll through
your customized data, then "0.0" will be displayed.
4. Step onto the scale BAREFOOT.
5. Weight will be displayed for 3 seconds. Remain on scale without moving!
6. Display will flash “bf” and “%”,
followed by your body fat
percentage.
7. Display will flash “H2O” and “%”,
followed by your body water
percentage.
8. The interpretive color bars will light up at the same time as your body fat
and body water measurements, showing you whether your results are normal
(green bar), lower (yellow bar) or higher than normal (red bar). Use color
bars as a guideline only and discuss any questions or concerns with your
healthcare provider.
9. Display will cycle through your measurements again and then automatically
turn off.
Using The Weight-Only Mode
For weight-only mode, no personal data entry is necessary.
1. Place scale on a flat, level surface.
2. Tap center of scale platform with foot to activate (display will flash).
3. Wait for "0.0" to appear in display window.
4. Step onto scale. Weight measurement will appear in display window.
INSTRUCTIONS FOR USE
Before Using Scale
1. Set switch on the back of the scale to measure in kg (kilograms) or lb
(pounds).
2. Set scale on floor. Surface must be level for accurate operation and safety.
Customizing Your
Thinner ® Body Analysis Monitor
Setting Data for Body Fat/Hydration Measurement
1. Tap center of scale platform with foot to activate digital display (display
will flash).
2. Wait for "0.0" to appear in display window.
3. Press SET button. The scale is now ready to input your personal data.
Enter User Number
• "P-01" will flash in display window.
• Press UP or DOWN arrows to select your individual
user number (four user numbers available: P-01
through P-04).
• When selected user number appears in display,
press SET button to save user number.
• The scale is now ready for you to enter your height.
Set Height
• "Ht" (height) will flash in display window.
• Press UP or DOWN arrows to scroll to your
height measurement.
• Press SET button to save height.
• The scale is now ready for you to enter your age.
Set Age
• "Age" will flash in display window.
• Press UP or DOWN arrows to scroll to your age.
• Press SET button to save age.
• The scale is now ready for you to enter your gender.
Set Gender
• The gender icons will flash in display window.
• Press UP or DOWN arrows to select male or
female icon.
• Press SET button to save gender.
Age
%
LIMITED TEN YEAR WARRANTY
Conair will repair or replace, at our option, your appliance free of charge for 120
months from the date of purchase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the defective product to the service
center listed below that is nearest you, together with your sales slip and $5.00
for postage and handling. California residents need only provide proof of
purchase and should call 1-800-3-CONAIR for shipping instructions. In the
absence of a receipt, the warranty period shall be 120 months from the date of
manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION
TO THE 120 MONTH DURATION OF THIS WARRANTY. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow
the exclusion or limitation of special, incidental, or consequential damages, so
the above limitation may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
05AD15054 IB TH402 comp.indd 4-6 6/12/06 3:50:27 PM