Attwood LED Waketower All-Round Light - Manual

LED W
AKE
TOWER LIGHT
5580
SA
VE THESE
INSTRUCTIONS
INST
ALLA
TION INSTRUCTIONS 09/02
69448
Rev
. B
FEA
TURES
The
Attwood LED W
aketower Light is designed for boats up to 39.6 ft (12 meters). It
features an impact resistant, UV
-stable polycarbonate housing. Light meets USCG
CFR 183.810,
ABYC
A-16 requirements, and all applicable standards as tested by
Imanna Labs, July 2008. 5580 is an
All-Round Light with 2 Nautical Mile visibility
.
REQUIRED FOR INST
ALLA
TION
Cordless drill with 1/8
″ and 1/4
″ (3mm and 6mm) bits.
•
Screwdriver
.
•
Two #8 or #10 stainless pan head screws per light.
•
Non-silicone sealant.
•
!
W
ARNING:
To
prevent personal injury
, disconnect the power source when installing or servicing this
product.
Always remove the boat from the water before using 120V
AC power tools.
LOCA
TION
All-Round Lights must be mounted a minimum of 1 meter above the sidelights, on a smooth surface where the 360° beam will not be obstructed. Light must not shine on operator or on anything in operator
’s
fi
eld of view
. (Figure 1)
IMPORT
ANT
:
Before drilling mounting holes, be sure that light shines within 5° of
horizontal
when the boat is
fl oating.
INST
ALLA
TION, DECK MOUNT
To
access mounting holes, gently twist lens helmet counterclockwise to remove.
1.
Place light in position as shown in Figure 2.
2. IMPORT
ANT
:
Before drilling, be sure that light will shine within 5° of horizontal
when the boat is
fl oating.
Drill 1/8
″ (3mm) pilot holes for both screws using base as a guide.
3.
Bring 12V DC (+) and (-) wires up through deck hole. Connect wires using
4.
waterproof crimp on butt joint connectors. Activate light to verify proper operation.
5.
Apply a thin bead of non-silicone sealant on underside of base to prevent water
6.
from entering hull or cabin. Align and fasten base with stainless screws. Do not over tighten.
7.
Snap light into base while aligning rib into slot.
8. FINAL
WIRING
!
CAUTION:
Power source must be positive 12V DC only
. All positive (+12V DC) wires must be
fused to protect the circuit.
Attwood Navigation Lights require a 1-amp fuse. Failure
to make proper connections and fusing will void product warranty
.
Neatly thread wires to dash avoiding any areas where abrasion or snagging may
1.
occur
.
Use waterproof crimp on butt joint connectors to attach wires to a switch on the
2.
dash that allows for two-position operation - one for running lights and one for anchor lights.
Test lights for proper operation. (Figure 3)
MAINTENANCE To
clean, wipe with damp cloth. Bulb is not serviceable.
A
TTWOOD LIMITED 10-YEAR W
ARRANTY
This
Attwood product carries a limited ten (10) year warranty
. This is a non-
serviceable (LED) light source, any attempt to open or service the light voids warranty
. See product catalog or attwoodmarine.com for details.
© 2009
Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331, www
.attwoodmarine.com
A
Figure 1
/ Figura 1
Figur 1 /
Abbildung 1
Figure 1
One meter or
A. 39-3/8
″
7º
B.
Figur 1
en meter eller
A. 39-3/8 tum 7º
B.
Figure 1
Un mètre ou 39
A. 3/8 po 7º
B.
Abbildung 1
1 Meter
A. 7º
B.
Figura 1
Un metro
A. 7º
B.
A
B C D E
F
Figure 2
/ Figura 2
Figur 2 /
Abbildung 2
Figure 2
One T
ime
Snap
A.
Straight Down
To
Secure, Not Meant To
Be Removed.
Lens Helmet
B. Base
C. 1/4
″ (6mm) Dia.
D.
Hole 1/8
″ (3mm) Pilot
E.
Holes Sealant
F.
Figur 2
Snäpper fast på
A. plats rakt nedåt, ej avsett att avlägsnas igen. linsskydd
B. fäste
C. 1/8-tums (3 mm)
D. styrhål hål med
E. 1-1/4-tums (19 mm) diam. silikonfritt
F. tätningsmedel
Figure 2
Enclenchement
A. direct vers le bas unique; non conçu pour être enlevé. Casque de lentille
B. Base
C. Avant-trous de 3
D. mm (1/8 po) Trou de 19 mm de
E. diamètre (1 1/4 po) Agent de
F. scellement sans silicone
Abbildung 2
W
enn das Licht
A.
einmal fest eingerastet wurde, sollte es nicht wieder entfernt werden. Linsenabdeckung
B. Sockel
C. 3 mm
D. Führungslöcher Loch mit 19 mm
E. Durchmesser Dichtungsmasse
F. nicht auf Silikonbasis
Figura 2
Ajuste una vez
A. hacia abajo para fi jarla; no está concebida para extraerse. Casco de las
B. lentes Base
C. Ori
fi cios guía de
D.
3 mm Ori
fi cio de 19 mm
E.
de diámetro Sellador sin
F. silicona
A
B
C
C
D
D
E
Figure 3
/ Figura 3
Figur 3 /
Abbildung 3
Figure 3
3-W
ay Switch
A.
1-Amp Fuse
B. Pos.
C. Neg.
D. 12V DC
E.
Figur 3
3-vägsström-
A. brytare 1 A
säkring
B.
pos.
C. neg.
D. 12 V likström
E.
Figure 3
Interrupteur à trois
A. positions Fusible d’un
B. ampère Pos.
C. Nég.
D. 12 volts CC
E.
Abbildung 3
3-W
eg-Schalter
A.
Sicherung 1
A
B.
Pos.
C. Neg.
D. 12 V Gleichstrom
E.
Figura 3
Interruptor de tres
A. vías Fusible de 1
B. amperio Positivo
C. Negativo
D. 12 voltios de CC
E.
B