B&M 45074 PRECISION SPORT SHIFTER - 88 - 00 HONDA - Manual

(Tall Leather), #80744 (Short Leather),
#80745 (Carbon Fiber look), #80746
(Billet Aluminum look), #80535 (Real
Carbon Fiber), #80554(Diamond),
#80555(JDM). These sturdy knobs are
ergonomically designed to better fit
your hand during hard-core performance
driving. These knobs incorporate an
innovative stick locating/locking method
that allows the knob to fit on virtually
any manual transmission stick.
INTRODUCTION
The B&M Short Throw Shifter can
be installed in less than an hour by
carefully following the instructions.
Read all instructions first to familiar-
ize yourself with the parts and proce-
dures. This kit contains all the parts
necessary to install the shifter.
DISASSEMBLY
We suggest the vehicle be allowed to
cool for an hour or two before you be-
gin since you will be working around
the exhaust system. The vehicle
should be raised so there is at least 2
feet of ground clearance for ease of in-
stallation and safety.
STEP 1. Unscrew the stock shift knob
and then raise and support the vehicle.
CAUTION: MAKE SURE THE VE-
9500697-04 Printed in the U.S.A.
This B&M Short Throw Shifter has
been designed to work on most 1988-
2000 Honda Civic/CRX/del Sol and
1990-2001 Integra models equipped
with a manual transmission. It has
been engineered to greatly reduce shift
throw and improve shifter feel. Check
the tool list at the end of these
instructions for the tools required to
install your B&M Short Throw Shifter.
Installation of the B&M Short Throw
Shifter can be accomplished by
anyone with minimal mechanical
experience.
When installing your B&M Short Throw
Shifter there are several other B&M
products you may wish to consider:
B&M Synthetic Stick Shift: #80287
a synthetic manual transmission fluid
formula engineered to get the best
performance out of your manual
transmission, transaxle or differential.
Formulated for racing and performance
applications, extensive testing shows
B&M Stick Shift provides total
lubrication protection for street and
heavy-duty applications as well. Stick
Shift provides outstanding oxidation
stability, extreme pressure protection,
anti-shear agents and foam inhibitors
that provide the tenacious capability to
keep on lubricating under extreme
conditions.
B&M Manual Shifter Knobs: #80743 HICLE IS RIGIDLY AND SECURELY
SUPPORTED, JACK STANDS,
WHEEL RAMPS OR A HOIST WORK
BEST, DO NOT USE JACKS ALONE.
STEP 2. Unhook the two rubber ex-
haust hangers near the catalytic con-
verter and carefully lower the exhaust
pipe. It may be helpful to place a small
crowbar between the exhaust pipe and
the floorpan.
STEP 3. Using a 12mm socket wrench
and 12mm box wrench, remove the nut
and bolt attaching the shift lever to the
change rod. Carefully lower the change
rod and allow it to hang out of the way.
STEP 4. Using a 12mm socket and
short extension, remove the two bolts
from the rear extension mounting rub-
ber. Allow the change extension to
drop slightly (it will still be attached to
the shift lever dust seal).
STEP 5. Use a 12mm box wrench to
remove the bolt holding the front of the
change extension to the transmission.
STEP 6. Using your forefinger, care-
fully roll the shift lever dust seal off of
the change extension. You can now
gently pull the change extension and
the shift lever from the vehicle.
STEP 7. Place the change extension
on a clean, flat surface and remove the
two change ball locknuts using a 10mm
socket (the bolts have a 10mm flat to
assist in removing the locknuts).
I
nstallation Instructions
Short Throw Shifter
1988-2000 Honda Civic/CRX/del Sol
1990-2001 Integra
Part Number 45074
©2003, 2001, 2000 by B&M Racing and Performance Products