Kidco K100 - Manual

K100 Safety Gate Installation Kit
To install all styles of safety gates in locations other than wood framed doorways, you will need
one installation kit for each gate side that is not being attached to a solid wood wall or door frame.
Some applications, such as wrought iron, might require two installation kits for each gate side. In
many cases even pressure mounted gates need an installation kit to allow for baseboards or
surfaces that are not parallel or to protect hard to replace wall coverings from gate damage.
Installation Kit Contents
Quantity Description
1
36” long hardwood board – knots and irregularities are normal. When installing
shorter gates, the board can be cut to approximately 1” taller than the gate.
1 2 ½” hardwood spacer
1 3/16” butterfly toggle bolt
1 3 ½” machine screw
1 3/16” wing nut
1 flat washer
2 1 ½” wood screws
1 2 ½” wood screw
2 18” long plastic tie straps
Before Installation
• Measure the opening and confirm that the gate purchased will accommodate
the opening width (top and bottom).
• Assemble the gate according to the manufacturer’s instructions to the point
where it is ready to be mounted into the opening.
• Consult a local paint store for a finish that will match the home’s woodwork.
• Tools required for use with this gate installation kit are: drill with bits, screw
driver, pliers and wire cutters/knife.
Wood Banister Installations – Wood Screws
(preferred method)
Most people hesitate to drill holes into their wood banisters. This concern is easily overcome
once it is understood that no tree ever grew in the shape of a wood banister and dozens of
holes may already be covered up with wood putty. For a little more than $1, hardware stores sell
putty sticks that fill such holes and match the color of the wood stain or paint once the gate has
been removed. Wood screws are the strongest installation and are recommended for the top
of a stairway when using any gate with this installation kit.
1. Place long board vertically against the banister where the gate will be mounted.
The board might need to be cut shorter to fit your banister. If necessary, use the
wood spacer at the top or bottom of the board to obtain a vertical mounting surface.
2. Drill a 3/32” pilot hole, (approximately ½” from the bottom) through the long board
(and wood spacer if being used) into any strong part of the post or handrail. Insert
1½” screw (or 2½” screw if using the wood spacer) and tighten.
3. Now you are ready to mount the gate hardware into the mounted wood installation kit.
Wood Banister Installations – Plastic Tie Straps
This method of installation is only recommended with hardware mounted wall gates.
1. Place long board vertically against the banister. Be sure the bottom end is resting on
the floor and flat against the square portion of the post.
2. Place one tie strap near the bottom where it will not slip down the long board or post.
This would most often be at the first round turning which is normally 6-12” from the bottom.
3. Insert the flat tip of the strap into back portion of the lock (3a) at the other end. (If you have
it backwards, it will not lock). Should you make mistake, a small screwdriver will release the
lock (3b) to reopen the strap lock. Pull very hard with the pliers until the board is tight against
the banister. Cut off any excess strap with wire cutters or knife.
4. Repeat process at the top of the board with the second tie strap.
5. Now you are ready to mount the gate hardware into the mounted wood installation kit.
Important – After installing the gate, test it to make sure the mounting board stays securely
in place. If it moves, use double-faced foam tape (available at hardware stores) on the
backside of the mounting board where it touches the banister post. If the board continues
to move or the straps slide down, you can cut small notches in the mounting board at
the desired height making sure the straps rest in the notch.
Hollow Wall Installations
1. Place long board vertically against the wall where the gate will be mounted. If you have
hardwood floors mount the board directly above the quarter round molding. In most cases,
use of the wood spacer will be necessary to obtain a vertical mounting surface.
2. Drill a 3/32” pilot hole (approximately ½” from the bottom) through the long board into the
baseboard. Check to make sure this hole location will not interfere with mounting the gate
hardware. Insert 1½” screw and tighten.
3. Drill a 13/64” or larger pilot hole, (approximately ½” from the top) through both pieces of the
wood, but not going through the wall at this time. Try using the 2½” wood screws to see if
you are lucky enough to hit a hidden stud. If no stud is present, then drill a ½” hole into the
wall only, and use the 3½” machine screw with the butterfly toggle bolt (3c). Securely tighten
the screw or bolt.
4. Now you are ready to mount the gate hardware into the mounted wood installation kit.
Wrought Iron Installations
Many older homes have metal wrought iron banisters and railings. The use of two installation
kits is recommended to act like a sandwich on the metal and provide a secure mounting surface
for the gate.
1. Position one long board on each side of the wrought iron. It might be necessary to use
one or both wood spacers at the top or bottom in order to have a vertical mounting surface.
2. Mark the location for the bottom machine screw, so when inserted it will rest upon the lower
beam of the wrought iron so it will not slide down. Drill the bottom hole through both long
pieces of wood the next drill bit size up from 3/16” (13/64” or 9/32”).
3. Insert 3½” machine screw from the side where the gate will be mounted. Add the flat washer
and tighten with the wing nut (3d). If the bolt extends too far (beyond the wind nut) be sure
to cut it off with a wire cutter or cover with several layers of tape to prevent abrasion.
4. Drill the top hole just below the top wrought iron hand rail. This will reduce the chance of the
installation board from slipping after the gate is installed. (Use the 3½” machine screw,
washer and wing nut from the second installation kit, for this top section.)
5. Now you are ready to mount the gate hardware into the mounted wood installation kit.
Brick, Concrete and Special Installations
This kit will solve the vast majority of installation application problems. However, special surfaces
such as brick, concrete block, and plaster will require additional hardware and advice from your
local hardware store or handyman. KidCo suggests that you consider hiring a local Baby Proofer
for the more complicated gate installations. It is difficult to explain special installation problems
over the telephone; however, KidCo welcomes your call, fax or email.
Common Sense Rules for Safety Use of Gates
• No gate should be entirely trusted to protect a child at any location, especially at the top of
a stairway. There is no substitute for constant adult supervision.
• Avoid gates that can be easily climbed. Some widely spaced plastic mesh gates allow toeholds
and opportunities for fingers, toes, arms and legs to get caught. The same is true in many
sliding panel models.
• Keep large toys away from the gate to discourage a child from climbing over it.
• To pass minimum safety standards some gates are only 22” high, which is an invitation for
danger when other family member step over them. This is also not a good example to set.
• Many plastic gates have rough edges and openings. Thoroughly inspect and lightly sand any
sharp edges remaining on the gate.
• Check the hardware frequently after installation to make certain all fittings and hardware
are secure.
• Discontinue use if the gate height is lower than three quarters of the child’s height.
Wood Banister Installations
– Plastic Tie Straps
Installation sur une rampe de bois
- avec vis à bois (méthode privilégiée)
Instalaciones en asamanos de madera
- Tornillos para madera (método preferido)
Hollow Wall Installations
Installation sur un mur creux
Instalaciones en paredes huecas Wrought Iron Installations
Installation sur le fer forgé
Instalaciones en hierro forjado Wood Banister Installations
– Wood Screws
Installation sur une rampe de bois
- avec vis à bois (méthode privilégiée)
Instalaciones en asamanos de madera
- Tornillos para madera (método preferido)
2
2
3
3
1a
1a
1b
1b