La-Z-Boy PowerReclineXR 08/11/2014-01/18/2015 - Manual (Page 6)

PowerReclineXR ® with Massage & Heat
Assembly Instructions
F IGURE 7 F IGURE 8
F IGURE 9 F IGURE 10
6. Align the red heating pad connectors and push the connectors together until locked (F IGURE 7).
7. Align the brown massage connector with the black massage connector and push the connectors
together until locked (F IGURE 8).
8. Gently rotate the chair back to the upright position so it is resting on its base. Do not allow the power
supply connector to be pinched between the frame and the floor.
9. Connect the power transformer connector into the power supply connector. Close the locking cover
to secure the connection (F IGURE 9).
10. Connect the 120 volt power cord to the power transformer (F IGURE 10). Do not plug in until instructed
in the Operating Instructions.
11. Proceed to the Battery Backup Assembly Instructions.
12. To remove the back, unplug the 120 volt power cord from the electrical outlet, and disconnect the
power transformer connector from the power supply connector. Reverse the Assembly Instructions steps.
Make this
connection
Make this
connection
Make this
connection
Power
Transformer
Power Supply
Connector
Make this
connection
120 Volt
Power Cord
11 10
PowerReclineXR ®
Rocking Loveseat Assembly Instructions
1. Place the furniture in the desired location; refer to Furniture Placement Guide.
2. Use a T-30 torx driver to loosen the threaded studs to approximately 1"; this measurement may vary
depending on the fabric and style. The threaded studs are located on the left side (sitting) of right side
(sitting) units.
3. Place the console (F IGURE 3) approximately 2" to the side of the left side (sitting) rocker recliner (F IGURE 1).
Position the console (with the threaded studs) slightly behind the recliner. Separate the fronts of the units
to be connected, about 6" apart. Pull the console forward until the threaded stud on the console engages
in the rear bracket on the recliner.
– To reduce the risk of serious injury:
• Provide a clear path for operation of the back and legrest. Place tables and area rugs
at a distance to allow the legrest to fully extend without rubbing or interference.
WARNING
– To reduce the risk of serious injury:
• The front of the unit must be raised to engage the front bracket. Please seek assistance if
you are unable to lift at least 21 pounds.
• Keep feet clear of the unit when lowering into position.
WARNING
4. Lift the front of the console approximately 3" off the ground, aligning it to the attachment bracket on the
left side (sitting) rocker recliner. Gently lower the threaded stud into the front attachment bracket (F IGURE 4).
Keep feet clear of the unit when lowering into position.
NOTE: Due to variations in upholstery and style, the threaded stud length may need to be adjusted to fit
into the attachment brackets or control gaps between units. Loosen or tighten the threaded studs to provide
adequate clearance.
5. Place the right side (sitting) rocker recliner (F IGURE 2) about 2" to the side of the console. Position the right
side (sitting) rocker recliner (with the threaded studs) slightly behind the console. Separate the fronts of
the units to be connected, about 6" apart. Pull the right side (sitting) recliner forward until the threaded
stud on the recliner engages in the rear bracket on the console.
NOTICE:
– To reduce the risk of product damage:
• Lift from the side frame. Do not lift from the upholstery or bottom of the legrest.
– To reduce the risk of serious injury:
• The front of the unit must be raised to engage the front bracket. Please seek assistance if
you are unable to lift at least 21 pounds.
• Keep feet clear of the unit when lowering into position.
WARNING
6. Lift the front of the right side (sitting) recliner approximately 3" off the ground, aligning it to the attachment
bracket on the console. Gently lower the threaded stud into the front attachment bracket. Keep feet clear
of the unit when lowering into position.
7. Adjust the glides on the console to level the unit, if necessary. Turn clockwise to lower and
counterclockwise to raise.
(Assembly Instructions Continued)