Smart Power Systems SmartNet II - Manual

USER'S GUIDE USER'S GUIDE
Data Line & Signal Protection Data Line & Signal Protection
Model A
Model C
www.smartpowersystems.com 1-800-882-8285
PN16000650 Rev.04-12
The new SmartNet II is the only
data line and signal protector
with easy installation
3 Features
• Easy installation with connection to ground
• Stand-alone data line and signal protection
• Protects any electronic equipment against surges that
come through the telephone and data line.
• Noticeably increases download speed (up to 200%)
•
• All units come with the necessary patch cables, except
on the coaxial and BNC models.
• No tools necessary for installation of Model A
• Available in colors black and computer gray
For T1, T3, 10/100/1000 Based-T, ISDN, DSL, etc.
• Handle data line with speed of over 300MHz
SmartNet II
2
Smart Power Systems Inc. is an engineering and
manufacturer of power quality products. The new
SmartNet II is the only data line and signal protector
with easy installation for telephone equipment/DSL
(RJ11), network (RJ45), big screen tv/cable (coaxial)
and CCTV/security system (BNC).
FOR SAFETY AND OPTIMUM PERFORMANCE,
THE SMARTNET SHOULD BE PROPERLY
GROUNDED.
THE USE OF THE SMARTNET IN LIFE SU-
PPORT APPLICATIONS WHERE FAILURE OF
THE SMARTNET IS EXPECTED TO CAUSE THE
FAILURE OF THE LIFE SUPPORT EQUIPMENT
IS NOT RECOMMENDED.
Specifications and Applications 4 Specifications and Applications 5
Specifications and Applications 6
Model A
Size (HxWxD) (In) : 1.37" x 1.31" x 3.31"
Weight: 0.11 Lb.
Model B
Size (HxWxD) (In) : 2.0" x 1.31" x 3.06"
Weight: 0.11 Lb.
Model C
Size (HxWxD) (In) : 2.12" x 1.31" x 3.06"
Weight: 0.16 lb.
7 Installation
The SmartNet protects your equipment from surges that come
through the data and signal line. To ensure that your equipment
is completely protected, use a TBF™ power filter or UPS-TBF
from Smart Power Systems.
1) SmartNet must be installed as close as possible to the
equipment to be protected.
2. Turn off all equipment.
3 Unplug the RJ11/45, Coaxial or BNC cable from the equip-
ment you want to protect and plug into the "IN" jack on the
SmartNet II. Plug the other end to the network jack or cable
wall jack.
4. Plug the provided network cable (RJ11 or RJ45 only) to the
"OUT" jack on the SmartNet II. Plug the other end of the pro-
vided network cable into the equipment you want to protect.
5. Connect the SmartNet unit to ground. See instructions on
pages 8-11.
RJ45
SN-Net5e
MODEL
IN/OUT JACK
CLAMPING VOLTAGE
AND PIN CONNECTION
7.5 Volts protecting
pins 1 through 8 for
Network
SN-NPOE
RJ45
SN-Tel
RJ11
75 Volts protecting pins
1 through 8 for
POE Network
300 Volts protecting
pins 4 and 5 for
phone line
APPLICATION
10/100/1000Based-T
Cat5e. For protection
of high speed
networked equipment
For protection of POE
(Power Over Ethernet)
network, T-1 equipment
For protection of
phone systems, fax,
answering machines
and DSL/modems
RJ11
300 Volts protecting
pins 4 and 5 also 3
and 6 for dual phone
line
SN-Tel2
MODEL
IN/OUT JACK
CLAMPING VOLTAGE
AND PIN CONNECTION
SN-TV
Coaxial
75 Volts for protecting
against surges between
center and shield
75 Volts for p
against surges between
center and shield rotecting
SN-BNC
BNC
For protection of phone,
answering machines
and fax with 2 phone
lines
APPLICATION
For protection of TV
systems, cable box
and DVR
For protection of
security systems,
CCTV and camera