Cambridge Audio Azur - Manual (Page 20)

20
Bass Augment can be a useful function with PLII material because this
encoding type does not include an LFE Channel. This would normally
mean that if all the speakers in your setup were set to ‘Large’, the
subwoofer would in fact be inactive (as no bass has been re-directed
plus there is no LFE channel). If it is desired to have the subwoofer
running with all Large Speakers and PLII encoding, enable Bass
Augment for PLII and then set the Crossover point and level by ear. A Sub
channel will now be created from the Front Left and Right channels
without filtering them. As with all adjustments it is a good idea to
experiment to determine what works best with your particular setup.
Note: In Advanced Sub On mode, the Subwoofer level control in the ‘Level
Calibration’ menu will be inactive. This is because this setting is
overwritten by the three appropriate Sub Trim settings from the ‘Advanced
Sub’ menu.
OSD setup
On-Screen Display is available on the Composite and S-Video outputs
only. (Not available on Component Video or HDMI.) Select the ‘OSD
Setup’ menu, select ‘OSD Video’ and use the Left and Right arrows to
select whether you would like the OSD video source to be Composite or
S-Video:
The OSD can be shown either on a blue background or overlaid on the
analog video. Select Background’ and use the Left and Right arrows to
select between ‘Blue’ and ‘Video’ backgrounds.
The OSD can also be shown in several different languages. To change
the OSD language highlight the ‘Language’ menu and use the Left and
Right arrows to select between English, Dutch, French, German,
Spanish, Italian, Norwegian, Swedish and Danish.
Press the OSD button again to exit and save the options.
OSD Setup Menu
TV Format : PAL
Background : Blue
OSD Video : Composite
Language : English
Return To Menu : [OSD]
Advanced bass management continued
The 340R features an IR Emitter input that allows
modulated IR remote control commands to be received
electrically by the unit. These control commands are
typically generated by custom installation (multi-room)
systems or remote IR receiver systems. An RS232 port is
also featured which allows the 340R to be controlled by C.I.
systems.
In addition the 340R features ‘direct’ IR/Control codes as well as toggle
codes for many of their features to simplify programming custom
installation systems. Special direct On/Off commands can be accessed
on the supplied remote control for teaching into C.I. systems as follows:
1. Press and hold the Standby/On button on the remote control. The
remote first generates it's standby (toggle) command. Keep the
button held down, after 12 seconds an AV receiver ‘On’ command will
be generated. If the button is kept held down for a further 12
seconds, an AV receiver ‘Off’ command is generated.
Repeat this procedure with the Mute, Sub On/Off, Stereo Mono and
Tuner FM/AM buttons to send On/Off commands. The Tuner FM/AM
button also provides unique FM and AM commands to allow switching to
a specific band.
A full IR code table and RS232 protocol for this product is available on
the Cambridge Audio website at: www.cambridge-audio.com
Custom installation (C.I.) use
In
IR Emitter
RS232C
Reset/Back-up memory
The 340R has a function that preserves the preset memory and other
settings. In the event of a power failure, or if the power cord of the unit
is disconnected from the mains outlet, the back-up memory will
preserve the preset memory for approximately one week. If the power
supply is interrupted for 7 days or longer, the memory settings will be
erased.
If it is desired to reset all settings to their factory defaults (or in the
unlikely event that the unit locks up due to an electrical discharge etc),
with the unit on and out of Standby mode press and hold the DVD and
5.1 Direct buttons on the front panel for three seconds:
‘RESET’ will appear briefly on the front panel display before returning to
Standby mode.
Mode/Store
DVD Video 1
Dolby Digital/
DTS
DSP
Mode
Pro Logic II Input
Mode
Stereo
Mode
Video 2 Video 3 Tuner FM/AM Tape/MD/CDR CD/Aux 5.1 Direct